The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old February 10, 2013, 11:22 AM   #1
droptrd
Senior Member
 
Join Date: September 22, 2011
Location: Illinois
Posts: 310
Harbor Freight rotary tumbler

Im thinking about picking up one of these rotary rock tumblers. Getting sick of replacing vibratory tumblers. My Hornady just crapped out ofter 2 years. Had a frankfort before that and a lyman before that. I know dillon has the lifetime warranty but I dont feel like spending $150 right now. Rock tumblers seem to be a more rugged design. Cant afford a Thumler Tumbler.

Has anyone here tried one of these harbor freight tumblers? The reviews show alot of reloaders using them?

http://www.harborfreight.com/dual-dr...ler-67632.html
droptrd is offline  
Old February 10, 2013, 12:13 PM   #2
mikld
Senior Member
 
Join Date: February 7, 2009
Location: Southern Oregon!
Posts: 1,053
Yep, used one for a lot of years. Never any problems, just loaded it up and plugged it in. Mine lasted until I tried to "improve" on the design so I could use a larger drum...

The only drawback is the drums are a bit small, I could clean only about 100 .38/.357 or 80-90 .44 magnums.
__________________
My Anchor is holding fast!
mikld is offline  
Old February 10, 2013, 12:17 PM   #3
droptrd
Senior Member
 
Join Date: September 22, 2011
Location: Illinois
Posts: 310
is that per drum? or for both drums?
droptrd is offline  
Old February 10, 2013, 12:31 PM   #4
HJ857
Senior Member
 
Join Date: January 9, 2007
Location: haslett, mi
Posts: 343
I've been that dual drum since 2006 and it's been great the whole time. It does break drive belts every six months or so though. I can fit 125 .223 cases per drum or 200 9mm cases, plus stainless pins. No problems. I use fewer pins that what most folks seem to. If you know the size of a Fancy Feast cat food can, I use half that can per drum.
HJ857 is offline  
Old February 10, 2013, 12:38 PM   #5
salvadore
Senior Member
 
Join Date: January 1, 2007
Location: Idaho
Posts: 1,813
Just a obsevation on rotary tumblers, I've had a thumbler for close to 30 years. Have replaced the rubber seal and a couple of belts, and have cleaned a gazillion cases with it.
salvadore is offline  
Old February 10, 2013, 12:57 PM   #6
oldpapps
Senior Member
 
Join Date: September 22, 2011
Location: Middle America
Posts: 445
Humm,

I got one a few years ago..... And the price has gone down!

I wet tumble with steel pins, a dob of Dawn and fill with water.
My biggest problem is I forget it is running. Brass gets very clean after 3 or 4 days.

Make sure the belt is lined up right and it will run forever (Oh, that's only me when I forget it's running).

Enjoy,

OSOK
oldpapps is offline  
Old February 10, 2013, 01:59 PM   #7
droptrd
Senior Member
 
Join Date: September 22, 2011
Location: Illinois
Posts: 310
Just ordered it. $50 why not.
droptrd is offline  
Old February 10, 2013, 07:48 PM   #8
big_bad_kitty
Member
 
Join Date: April 22, 2010
Posts: 72


Had mine for about 4 years now and not one problem. It holds give or take 2,500 rounds at a time and it does a wonderful job! I did not install the mixing vanes on the inside of the tub and use about 20 pounds of media, 1/2 corncob and the other crushed walnut. I use a capful of Brasso for every other load and my brass come out looking like new! I run them for three hours and once in a while I forget while it is running and it might go 4 hours before I catch it. Also had problems with the vibrating kind then shifted to rotary. Never could get enough in them at once and just gave up on the small ones. Gave $199 less 20% coupon and thought I had a real bargain. I looked today and HF running them for $139 and use a 20% coupon to get right at $110! That is a steal if you ask me!!
__________________
NRA Endowment Life Member - TX Concealed Handgun Instructor
Experience - What you get when you don't get what you wanted!
texasconcealedhandguninstructor.com
big_bad_kitty is offline  
Old February 10, 2013, 08:51 PM   #9
Icedragon
Member
 
Join Date: January 28, 2013
Location: Middle Tennessee
Posts: 28
That is sweet. Take it to the range with a sign saying put all brass here
They do have timers that you plug in you could use.
__________________
Do not expect a warning shot !!!

Last edited by Icedragon; February 11, 2013 at 12:21 AM.
Icedragon is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 03:27 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07865 seconds with 9 queries