The Firing Line Forums

Go Back   The Firing Line Forums > Hogan's Alley > Handguns: The Semi-automatic Forum

Reply
 
Thread Tools
Old January 27, 2013, 11:02 PM   #1
Nageljo
Junior Member
 
Join Date: August 29, 2010
Posts: 3
New Ruger 22LR pistols

I have been eyeing one of the new Ruger 22/45 Lite pistols with the factory threaded barrels. I am assuming that they have the same reliabilty/issues as the MK I/II/III but I figured I would ask for some first hand experiences.

Thanks
Nageljo is offline  
Old January 28, 2013, 02:06 AM   #2
+1k ammo
Senior Member
 
Join Date: January 9, 2013
Posts: 191
I do not have one, but they looked good at the gun show where they were on display and have heard good things about them.

I was interested and probably would get one, but the threaded barrels are an issue (banned in my neck of the woods) so if it is ok where you live I would go ahead and get one.

I think they looked pretty good too, but others who have actually shot one should chime in.
+1k ammo is offline  
Old January 29, 2013, 12:21 AM   #3
Nageljo
Junior Member
 
Join Date: August 29, 2010
Posts: 3
I have also been considering the M&P 22lr. I have a M&P in 9mm and love it. Is the 22lr roughly the same size or is it a smaller version?

Anyone have experience with them?
Nageljo is offline  
Old January 29, 2013, 05:12 PM   #4
flybuddy
Member
 
Join Date: January 25, 2013
Posts: 22
I've had one for about a month now and have run a lot of rounds through it. Good feel, very consistent groups and almost never has any FTFs regardless of what ammo. I bought it because of all the good reviews I had seen on net, guess they were accurate.
flybuddy is offline  
Old January 29, 2013, 06:44 PM   #5
Niner4Tango
Senior Member
 
Join Date: May 28, 2007
Location: Vancouver, WA
Posts: 250
A suppressor would be fun!

Ruger MKI/II have issues?
Niner4Tango is offline  
Old January 29, 2013, 07:41 PM   #6
Venom1956
Senior Member
 
Join Date: October 4, 2008
Location: WI
Posts: 3,027
Ruger mk series of pistols are fantastic. You can't go wrong with one of them.

The M&P22 doesn't have much in common with the actual m&p pistols. I believe Umarex makes them. I wouldn't place them in the same league as a mk 2 or 3.
__________________
E-Shock rounds are engineered to expend maximum energy into soft targets, turning the density mass into an expanding rotational cone of NyTrilium matrix particles, causing neurological collapse to the central nervous system.- Yeah I can do that.
I guarantee you will know it if a bicyclist hits your house going 1000 mph.
Venom1956 is offline  
Old January 30, 2013, 12:42 AM   #7
cal10
Member
 
Join Date: January 27, 2013
Posts: 37
I heard that the M&P 22 was made by Walther for S&W, It's a great gun but I chose the Ruger SR22 because it was more compact and felt great at the LGS. I've got about 2500 rounds through it in less than a month, and can't stop going to the range with it. It's awesome, it also has double action which the M&P 22 doesn't have.
cal10 is offline  
Old January 30, 2013, 12:42 AM   #8
tom234
Senior Member
 
Join Date: February 14, 2008
Location: Kansas
Posts: 752
Quote:
I have been eyeing one of the new Ruger 22/45 Lite pistols with the factory threaded barrels. I am assuming that they have the same reliabilty/issues as the MK I/II/III but I figured I would ask for some first hand experiences.
What relaibility issues ? I don't know of any and I have both a MKIII & 22/45
tom234 is offline  
Old February 1, 2013, 12:50 AM   #9
Nageljo
Junior Member
 
Join Date: August 29, 2010
Posts: 3
I simply meant that I am assuming that they are reliable as all get out and are kind of a pain to re-assemble if you tear one down. I think they are about as bullet proof as it gets, I just didn't know if anything had changed since they changed to a poly lower half.
Nageljo is offline  
Old February 1, 2013, 12:53 AM   #10
JohnKSa
Staff
 
Join Date: February 12, 2001
Location: DFW Area
Posts: 18,419
The MkIII series have a magazine safety which adds a hassle/difficulty factor to the disassembly/reassembly procedure.
__________________
Did you know that there is a TEXAS State Rifle Association?
JohnKSa is offline  
Old February 1, 2013, 05:02 AM   #11
Pilot
Senior Member
 
Join Date: December 21, 2000
Posts: 3,664
You can still get a both steel framed Ruger (MK III) and a polymer framed (22/45). The MK III added a Loaded Chamber Indicator and magazine disconnect safety which many DO NOT LIKE, and remove with a few replacement parts.
__________________
Pilot
Pilot is offline  
Old February 1, 2013, 05:19 AM   #12
CajunBass
Senior Member
 
Join Date: May 6, 2005
Location: North Chesterfield, Virginia
Posts: 3,459
The Ruger MK series of pistols are a bit harder to strip down/reassemble than say a Glock or something like that, but it's not so complicated that a person with normal skills can't do it. It's just a matter of understanding what you have to do, following the directions, and getting the parts worn together (they are tight at first).

Read and understand the directions. Every step is important. If they say point up or down, magazine in, magazine out..it's important. You can't skip that. And when it tells you to use a rubber mallet...use a rubber mallet. They're not kidding. The parts fit together that tight at first. You will not hurt anything.

Two things I had trouble with at first that aren't clear in the directions, or at least I didn't catch them. Removing the upper from the lower. I don't think you really need to do this...gunscrubber is your friend...but if you want to, you smack the rear of the upper to remove it, the front to reset it. After a few times you probably won't have to. I have one old Standard that just falls apart when I pull the mainspring out.

And in the reassembley instructions, at one point, it says "Let the hammer fall forward" or something along those lines. Well none of mine ever "fell" anywhere. They had to be pushed. A pencil, or a thin screwdriver work fine.

If you're going to use Gunscrubber, and I recomend it, make sure you (1) remove the grips first. (2) And if you're working on a 22/45 with it's polymer frame, be sure you use "polymer safe" Gunscrubber. It will work on metal frame guns too, so that's the safe one to buy anyway.

Most of the time I just flush them with gunscrubber, run a patch or two through the bore, and clean what I can reach with a Q-tip. I don't disassemble at all. Then when I do, I don't go much futher than pulling the bolt and flushing. The only times I've ever pulled the uppers were with old guns I bought used.

You'll need to put a few drops of oil here and there on the internals, and give it a good wipedown afterward of course.
__________________
For God so loved the world, that He gave His only begotten Son, that whoever believes in Him should not perish, but have everlasting life.
John 3:16 (NKJV)
CajunBass is offline  
Old February 1, 2013, 06:17 AM   #13
plateshooter
Senior Member
 
Join Date: September 29, 1999
Location: N.E. Ohio
Posts: 522
As for the Ruger Lite. We had a couple shooters in our NRA program last summer that had those guns. One was a woman who we could not convince to hold on to the pistol firmly and she couldn't get through one mag with out a malfunction.

The gun is so light that it needs a firm grip to let it function properly. Other than that, the gun was accurate, and when held properly, it functioned fine.
__________________
Make a hole
plateshooter is offline  
Old February 2, 2013, 09:04 PM   #14
9mmsnoopy
Senior Member
 
Join Date: December 14, 2004
Location: Thrillsville ,Tx
Posts: 903
I have one and like it, its fun to shoot and accurate enough but it doesnt like bullets that are'nt copper coated at all, may not all be like that, but mine sure doesnt care for them. Otherwise its all good.
__________________
beretta cx4 storm .40 caliber
sig P290
Kahr PM9 Glock 26
Bushmaster AR15
9mmsnoopy is offline  
Old February 2, 2013, 11:00 PM   #15
GrailKnight
Member
 
Join Date: April 8, 2010
Location: PA
Posts: 47
The only issue with Ruger Mk pistols is the take down being archaic.
Other then that every one I own functions flawlessly every single time
and actually shoot better dirty (my personal observation).
__________________
Who Dares Wins!
GrailKnight is offline  
Old February 3, 2013, 12:01 AM   #16
CTS
Senior Member
 
Join Date: November 6, 2011
Location: NE Georgia
Posts: 1,070
I love my '69 Model Mark 1 target so much that I just bought another '54 model Mark 1 target. They are a little bit of a pain to tear down but after a few times it is like riding a bike. It becomes second nature.
CTS is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 11:18 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.09898 seconds with 7 queries