The Firing Line Forums

Go Back   The Firing Line Forums > The Hide > The Dave McCracken Memorial Shotgun Forum

Reply
 
Thread Tools
Old January 28, 2013, 01:57 AM   #1
losixxx
Member
 
Join Date: April 29, 2012
Location: KY
Posts: 24
Stoeger condor & Stoeger STF 300 o/u

Was looking at to finding a affordable over and under and I was recomended the Stoeger looked at there website and I found the condor went to Dicks sporting goods website and seen the STF 3000. So hear is a few questions

1) What is the difference between the two?

2) Is there another over/under in ther range of $450 to consider?

3) Are these a decent firearm?

4) Is Benelli the maker of Stoeger?

Thanks for your help and replies

Last edited by losixxx; January 28, 2013 at 02:12 AM.
losixxx is offline  
Old January 28, 2013, 09:29 AM   #2
BigD_in_FL
Junior member
 
Join Date: December 20, 2012
Location: The "Gunshine State"
Posts: 1,981
In reverse order:


Beretta is the parent company of both Benelli and Stoeger; however they are independent makers. Stoegers are, IIRC, made in Turkey.

Decent? That will depend on what your intended usage is. Their quality has been hit and miss - in short, the ones that work do OK, the ones that don't require repairs. Handling is not what you would get with a better made gun, nor are the triggers as good. You need to check the POI/POA to see how well the barrels are regulated

In that price range, personally, I would not recommend an O/U that I would use for anything serious - whether targets, hard hunting use or HD

Between the two models, the STF is not listed on their site. It is my understanding, it is made exclusively for Dick's. I would suspect they are basically the same
BigD_in_FL is offline  
Old January 29, 2013, 01:21 PM   #3
Jimbo-Indy
Senior Member
 
Join Date: August 27, 2008
Location: Indianapolis, IN
Posts: 235
I bought a Condor Competition about 2 1/2 years ago. Mine was made in Brazil, not Turkey. Overall, not bad for the price, $610 out the door at Dick's. Did have some initial problems: stock not inletted properly, hammer spring for top barrel was dragging, causing light primer strikes; trim covering the space between barrels is glued on, came loose, had to re-glue with better adhesive; after patterning, need to change out the machine screws/spacers to get proper adjustment on comb (simple hardware store stuff). Since then it's worked fine. Triggers aren't bad. About 4000 rounds so far and still gong (I'm just a hobbiest @ trap). If you are handy mechanically, it's probably OK, If not, look somewhere else. For me, I was able to get into trap shooting when I had little $ to invest. It isn't a Browning, etc. but it will do the job if I do mine. Every now and then a friend lets me shoot his Parrazi (we are very similar in size/fit). I always slam it closed as I am not used to the smooth action vs the stiff Stoger.
Jimbo-Indy is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 12:28 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07315 seconds with 9 queries