The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old January 14, 2013, 03:17 PM   #1
RANGER94
Member
 
Join Date: December 18, 2010
Posts: 24
Tips Needed for reloading cast bullets

Hello everyone,
I have been reloading on again and off again for about 20 years. For some unknown reason - I have never loaded cast bullets. I am getting ready to load some .44 mag & .45 colt cast bullets which I purchased from King's Shooting Supply, specifically Roger's better bullets. Can you offer some tips or learning experiences? Is there any major difference for assembling cast vs. jacketed?

Thanks!

Ranger94
RANGER94 is offline  
Old January 14, 2013, 06:16 PM   #2
grubbylabs
Senior Member
 
Join Date: October 11, 2009
Location: Hansen Idaho
Posts: 1,442
Unless you are loading max, you should be fine. If they are sized for your barrel and the alloy is right for the speed you are pushing , you won't have any problems.
__________________
* (Swinging club) Whack! whack! whack! *

Nope, the old nag's still dead .
(Capt Charlie)
grubbylabs is offline  
Old January 14, 2013, 06:40 PM   #3
Shotgun693
Senior Member
 
Join Date: September 3, 2011
Location: Poteet, Texas
Posts: 959
At times I've had to bell the case mouth just a bit more to seat a cast bullet. The harder the cast bullet the faster you can drive it without leading. Other than that you should have no problems. IF you do have some leading and have trouble cleaning it out push a wad of 0000 steel wool down the barrel.
Shotgun693 is offline  
Old January 15, 2013, 09:21 AM   #4
reloader28
Senior Member
 
Join Date: October 13, 2009
Location: nw wyoming
Posts: 952
Better than steel wool is using Chore Boy. Wrap a little of it around the brush.

You have to make sure the bullet fits the gun. Slug the bore and get bullets that are .002 bigger than the groove dia. The 45 will probly be fine with .452, but you'll probly need .431, maybe .432 for the 44.
reloader28 is offline  
Old January 15, 2013, 09:56 AM   #5
Unclenick
Staff
 
Join Date: March 4, 2005
Location: Ohio
Posts: 10,406
There is also Sharpshoot'R's Wipe-Out No-Lead. You put it in the bore and let it sit for an hour and it actually reacts with the lead to turn it into a crumbly black substance that patches out with a cloth patch.

To get revolvers to shoot with best accuracy can take a little bit of work. With any cast bullet gun you want to slug the bore to learn its groove diameter. For a revolver you also want to slug every chamber and make sure they are uniform within a half thousandth or so and that they are all at least a thousandth bigger than the groove diameter of your barrel. One and a half thousandths bigger is ideal for commercial cast bullets, which are 0.001" over standard groove diameter. Two and half thousandths bigger is ideal for cast bullets you size 0.002" over groove diameter (most accurate in my revolvers).

If you don't know how to slug a barrel search this site. Ignore the YouTube Commanders who use calipers and get an OD thimble micrometer for this so you can get better precision and resolve tenths of a thousandth. If you have a 5 groove barrel you can send them to Matt Dardas for measuring.

If you have any kind of constriction in your bore (common in revolvers where the barrel screws into the frame), you need to remove it by firelapping or else you at least need to polish the bore well in the constricted area so it can bump back up after passing the constriction without gas bypass. Gas bypass causes leading and bullet base asymmetry which is pretty hard on accuracy. This article is helpful.
__________________
Gunsite Orange Hat Family Member
CMP Certified GSM Master Instructor
NRA Certified Rifle Instructor
NRA Benefactor Member
Unclenick is offline  
Old January 15, 2013, 10:25 AM   #6
jimkim
Senior Member
 
Join Date: July 3, 2008
Location: middle GA
Posts: 319
The LASC link Unclenick posted will get you to their website. Read this while you're there. http://www.lasc.us/Fryxell_Book_Contents.htm
__________________
Jan. 4, 2007 gasoline $2.10 gal....HMMM?
jimkim is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 12:06 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.06896 seconds with 7 queries