The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old January 11, 2013, 10:26 AM   #1
Contrast Man
Senior Member
 
Join Date: November 2, 2011
Location: Illinois
Posts: 170
Light-Mid .357 loads

I just bought a S&W 686 and I have a few questions for loading for it. The load I plan on starting with from Lyman's 49th is 125gr Berry's plated with Bullseye powder. As far as charge weight, would I be able to use data from 38 spl in a .357 case? The range for the 38 spl loads goes from 3.2gr to 4.4gr, but the .357 range is 6.5gr to 8.6gr.

I'm fully aware of the limitations of plated bullets and have no intention of loading them even close to the high end.

If using lighter loads, would a magnum primer still be required or would it be sufficient to use a standard small pistol primer?

Thanks for your input!
Contrast Man is offline  
Old January 11, 2013, 10:37 AM   #2
Ifishsum
Senior Member
 
Join Date: September 15, 2005
Location: Oregon
Posts: 698
You can load a .38 special recipe into a .357 case - and pretty much anywhere in between .38 and .357 data if you like. Because of the larger case size, the same load in the larger case will be a bit lower pressure, so at least a small bump might be needed to achieve the same result.

Primer choice is dictated by the powder used - not the cartridge. Most load books will indicate when a magnum primer is recommended, most often that's with spherical powder like H110. Bullseye does not need a magnum primer in any case.
Ifishsum is offline  
Old January 11, 2013, 10:39 AM   #3
Jim Watson
Senior Member
 
Join Date: October 25, 2001
Location: Alabama
Posts: 10,917
There would never be a need for a magnum primer with Bullseye.

Using .38 Special data in .357 brass would give somewhat lower velocity because of the greater volume... unless you seated the bullets .135" deeper, which would not likely be an option with 125s.

Do be careful, the only gun ever demolished on our range was a .357 loaded with Bullseye at the high end. A double charge will fit and will blow it up.
Jim Watson is offline  
Old January 11, 2013, 11:02 AM   #4
Contrast Man
Senior Member
 
Join Date: November 2, 2011
Location: Illinois
Posts: 170
Thanks for the quick responses!

It's good to know I won't have to buy a new type of primers and can just use what I have in stock right now.

Also good to know that there will be a slightly lower velocity due to the extra space from .38 to .357. I like to think I'm good at keeping an eye on charge throws, but I also use an RCBS Lockout die which, while not absolutely fullproof, does help.
Contrast Man is offline  
Old January 11, 2013, 11:07 AM   #5
L_Killkenny
Senior Member
 
Join Date: February 2, 2007
Location: Iowa
Posts: 2,676
You should be fine with Bullseye but I don't like it with some other powders, even Unique. As I stated on another post today some powders don't like to be loaded light but Bullseye is traditionally used for light and target loads.

Like stated above you'll probably have a little less velocity using the .38sp loads in .357 cases. It was recommended to me that if I want to recover some of that loss add .5gr to the load OR use a mag primer. No, you don't need a mag primer for bullseye but it seems to bring the pressure up to compensate for the added case volume.
L_Killkenny is online now  
Old January 11, 2013, 10:51 PM   #6
GP100man
Senior Member
 
Join Date: August 1, 2007
Location: Tabor City , NC.
Posts: 1,914
With fast powders I always inspect the powder twice before seating .

I`ve found with fast powders ya don`t need mag primers .

& with fast powders in the 357mag when ya reach `bout 1k fps they get a little spiky in pressures, & keepin the plated bullets under or near 1k is a good idea.
__________________
GP100man
GP100man is offline  
Old January 11, 2013, 11:54 PM   #7
joneb
Senior Member
 
Join Date: December 10, 2005
Location: Central , OR
Posts: 1,729
I have loaded 140gr Raineer FP plated with 8.2gr of Accurate #5 and standard primers with excellent accuracy from a 4 and 2.75" 357 mag.
joneb is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 11:55 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07949 seconds with 7 queries