The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old January 10, 2013, 07:10 PM   #1
Sphawley
Senior Member
 
Join Date: June 9, 2010
Location: Las Vegas
Posts: 272
Lyman Universal Case Trimmer

Working on my first batch of reloads, Im using some brass that needs to be trimmed already. Starting off with the full cycle you could say...

Im struggling to get my Lyman universal case trimmer to the correct length for .308 of 2.015, initially I slowly trimmed a case to this correct length and then set it in there and then pushed the cutter up against it and set the set screws to hold. However this process didnt exactly work out for some reason.

What am I doing wrong is there a better way to approach this? How do you get the cutter set correctly?
__________________
If guns kill people, then pencils misspell words, cars make people drive drunk, and spoons made Rosie O' Donnell fat!
Sphawley is offline  
Old January 10, 2013, 07:20 PM   #2
m&p45acp10+1
Senior Member
 
Join Date: May 3, 2009
Location: Central Texas
Posts: 3,307
I had the same trimmer. I used a few pieces of new brass to set it when I started. One thing is not to push in too hard when turning the brass. Another is make sure you have the trimmer mounted to something solid. I tried at forst to work with it on a table, not pushing in on it too hard. Lengths were all over the place. I mounted it to my bech with good nuts and bolts very solidly. That helped out a great deal.

I traded it off for a lead melting pot, after I got a Lee trimmer lock stud, and case length guage for the caliber I was trimming, and it works with my drill.
__________________
No matter how many times you do it and nothing happens it only takes something going wrong one time to kill you.
m&p45acp10+1 is offline  
Old January 10, 2013, 10:40 PM   #3
deepforks
Member
 
Join Date: October 15, 2011
Location: Southwest Idaho
Posts: 89
+1 for the lee. i have the same for all my calibers. great tool.
deepforks is offline  
Old January 10, 2013, 11:04 PM   #4
rg1
Senior Member
 
Join Date: November 6, 2001
Posts: 752
Yes, don't push hard at the end of the cut. Make a few turns after the collar stops feeding but not with high pressure. The set screws and collars can slip if you push too hard. Make sure your pilot isn't tight in the case mouth. Shouldn't be loose but shouldn't have any binding. Lube the shaft and collar where it bottoms out. Light gun grease works well on mine. If your pilot is snug chuck it in a drill and sandpaper it until it slides easy into case necks. I like my Lyman Universal but it has some issues for me. Don't like the fiber bearing and especially don't like the collar bottoming out on the aluminum bearing housing. Love the chuck and the cutter is sharp and cuts well. I still can't get as accurate a length as I can on my Forster trimmer.
rg1 is offline  
Old January 11, 2013, 01:00 PM   #5
oneoldsap
Senior Member
 
Join Date: September 16, 2009
Location: I live in the foot of the Green Mountains of Vermont
Posts: 1,585
Piece of cake

When setting up your trimmer for a particular case , make sure to chamfer and deburr before measuring the case you are using to set your length . Or you won't get consistant measurements . Trim , deburr, campher , measure , adjust trimmer as needed . I always put the fine (outer) collar in the middle of it's adjustment range before starting . Put a case in the trimmesr and move the Inner collar up tight against your trimmer , with the cutter tight against the case mouth . Then turn the outer collar away from the trimmer body , to make cases shorter , inwards to make them longer . I'm thinking your problem was not deburring before measuring your sample . Am I right or wrong ? I have been using the Lyman universal for god knows how long . If you spring for the carbide cutter , it will probably last a lifetime !
oneoldsap is offline  
Old January 11, 2013, 06:38 PM   #6
Scorch
Senior Member
 
Join Date: February 13, 2006
Location: Washington state
Posts: 11,431
Set up the trimmer for rough length measurement that way, but use the fine thread adjustment that is in the spindle stop for getting it right on.
__________________
Never try to educate someone who resists knowledge at all costs.
But what do I know?
Summit Arms Services
Taylor Machine
Scorch is offline  
Old January 11, 2013, 08:27 PM   #7
Sphawley
Senior Member
 
Join Date: June 9, 2010
Location: Las Vegas
Posts: 272
Im unsure of how to get these spindles working correctly, pardon my inexperience...but it feels like there is a significant amount of force that needs to be used to turn these spindles even after loosening the set screws.

The shaft appears to be lubricated so I dont feel that is the issue. I tried looking for a YouTube video showing this but i have been unsucessful...Hopefully a little more guidance will get me on track!

All the tips are a huge help so far, I think this is the last part giving me trouble...
__________________
If guns kill people, then pencils misspell words, cars make people drive drunk, and spoons made Rosie O' Donnell fat!
Sphawley is offline  
Old January 11, 2013, 09:06 PM   #8
wncchester
Senior Member
 
Join Date: December 1, 2002
Posts: 2,832
All case trimmers have to be properly adjusted, there's no way around that. Well, all except Lee's very good trimming tools with a fixed stop rod.
wncchester is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 05:24 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.08135 seconds with 7 queries