The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old January 13, 2013, 06:54 PM   #1
Lilswede1
Senior Member
 
Join Date: September 8, 2008
Location: NW Wash State
Posts: 181
How do you keep track of loading dates?

I load .223 for a friend who does not keep spent cases separated very well.
Anyone have a good method of marking the reloads so that when you get them back you know what they are and how old?
Lilswede1 is offline  
Old January 13, 2013, 06:58 PM   #2
1-DAB
Senior Member
 
Join Date: May 5, 2010
Location: Santa Fe, NM
Posts: 154
Check case length and check for head separation and neck splitting. Reload until worn out.
1-DAB is offline  
Old January 13, 2013, 07:03 PM   #3
OEF-Vet
Senior Member
 
Join Date: October 23, 2011
Location: Backwoods, PA
Posts: 284
I color my primers with a set of permanent markers. I then fill my log in and put a dot of that color for each load batch. I have 16 colors and haven't run out yet as I usually shoot up a batch before I get out of the primary colors. Since I only mark the primers I can re use that color once I de prime the brass.

Sent from my HTC PH39100 using Xparent Green Tapatalk 2
OEF-Vet is online now  
Old January 13, 2013, 07:10 PM   #4
Hawg
Senior Member
 
Join Date: September 8, 2007
Location: Mississippi
Posts: 11,753
I don't try to keep track. I also will not reload for anyone else.
Hawg is offline  
Old January 13, 2013, 08:32 PM   #5
Goatwhiskers
Senior Member
 
Join Date: April 8, 2009
Location: Batchelor, La.
Posts: 471
Amen, Hawg. Swede, there's too much liability associated with loading for someone else. Things do happen, some of them to old experienced loaders. Remember, when something happens, whether injury or death, my fault, your fault, nobody's fault, when the lawyer gets thru with you in court it WILL be your responsibility. Your choice. GW
Goatwhiskers is offline  
Old January 13, 2013, 10:53 PM   #6
Tim R
Senior Member
 
Join Date: November 30, 2004
Location: God's side of Washington State
Posts: 1,601
Yep, when some one asks me to reload for them I offer my equipment and the time to show them how to do it.

I am very much into keeping track and use a reloading log. I mark the date along with the data on the bullet supplied stickers. If I need the box for more loaded ammo the fired cases go into a zip lock bag with a note about the brass.
__________________
God Bless our Troops especially our Snipers.
Tim R is offline  
Old January 14, 2013, 09:20 AM   #7
Rifleman1776
Senior Member
 
Join Date: April 25, 2010
Location: Arkansas
Posts: 3,309
I write the dates and other info on labels I stick on the storage boxes. Simple. The empties go back in the same box. I also reload until a cartridge fails. After a couple fails from the same box I anneal the whole lot.
Rifleman1776 is offline  
Old January 14, 2013, 04:10 PM   #8
BigJimP
Senior Member
 
Join Date: February 23, 2005
Posts: 11,396
I don't keep track of how many times a case has been reloaded....

The only system that might work ...is using different colors of permanent markers on the base...

But I sure wouldn't load for anyone else either...way too much liability / and I'm not confident my homeowner's liability insurance would defend me if something happened ( especially if I did it for money )..??? ....but I sure would feel bad if a buddy blew up a weapon, let alone if someone got hurt...so its not worth it, on a lot of levels !

I just tell friends, I'll help mentor them if they want to buy their own equipment ...help them with setup, etc...but if they want to reload, they need to invest in equipment and the time...
BigJimP is offline  
Old January 14, 2013, 04:22 PM   #9
jcwit
Senior Member
 
Join Date: October 28, 2007
Location: Upper Indiana
Posts: 593
As others have said, I reload till I see signs of failure, split necks, loose primer pockets, etc.

As far as rteloading for someone else? NEVER!

Amazing how fast you'll loose a lifelong friend when he looses a hand.
__________________
U.S. Army Veteran
NRA Certified Range Officer
jcwit is offline  
Old January 14, 2013, 05:42 PM   #10
hooligan1
Senior Member
 
Join Date: July 18, 2010
Location: Independence Missouri
Posts: 3,337
I develope and test loads, after I shoot a certain test load I inspect thecases and primers for excessive pressure, then I dump'em back into the spent case bucket.
If I run into cases that show any sign of too much pressure I set those aside as to inspect them after I resize those dudes. I don't mark anything, when the load comes around to what I think it should be then I get new or oncefired brass and load at least fifty, and put them up for season or for fun.
Also I don't load for anybody outside my house, although if I'm at the range and have extra I will share with my #1 son,(cause he never brings enough) but thats it.
__________________
Thanks for coming!
hooligan1 is offline  
Old January 14, 2013, 06:14 PM   #11
5R milspec
Senior Member
 
Join Date: December 11, 2009
Location: South Carolina
Posts: 360
If it helps I keep little black books in each ammo box.The dollar store has them 3 in a pac for a dollar.

I write all info from loads to how many times the brass has been shot.Keep dates posted all so for the brain ( I cannot remember a thing )
__________________
life is great but its better when you can own as many guns you wish to own.for me I haven't bought enough yet.
5R milspec is offline  
Old January 14, 2013, 06:34 PM   #12
m&p45acp10+1
Senior Member
 
Join Date: May 3, 2009
Location: Central Texas
Posts: 3,310
I inspect cases. If something does not seem right then I use a pair of pliers to bend the brass so that it is not able to be used again. I then put it into my recycle bucket.

Step one look for obvious signs of bad brass. Splits, separation rings, badly bloated cases, ect. ect.

Step 2 For bottle necked cases, and .30 Carbine. I paper clip test for seperation by using a bent paper clip inside. If a case has a cut in it the paper clip will catch. I crush those, and into the recycle bucket they go.

Step 3 Size. Then measure.

Step 4 Trim if needed.

Step 5 Prime. If the primers feel like they are seating too easy then I remove the primer, and scrap the case.
__________________
No matter how many times you do it and nothing happens it only takes something going wrong one time to kill you.
m&p45acp10+1 is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 08:00 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.09446 seconds with 9 queries