The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old January 10, 2013, 09:47 AM   #1
Belve
Member
 
Join Date: October 2, 2012
Posts: 58
first time reloader needing advice

So i have just ordered a lee turret kit, powder, brass and dies. I am looking to reload 10mm pistol and 5.7x28 my first question for target practice what is the best and most cost effective bullet for each of those calibers? my second question is what type of primers do those calibers take? Small or large? lastley again for only target practice what is the best bullet weight for each of those?

Thanks in advance for any help
Belve is offline  
Old January 10, 2013, 10:15 AM   #2
velillen
Member
 
Join Date: October 20, 2012
Posts: 88
Look in your reloading book for primer size. The 10mm I believe is a large pistol off the top of my head (but double check). The 5.7 is probably a small bit again double check.

Cheapest bullets will be cast lead. Can be found for around 60-70 per 1k. But lead can be Smokey and you might not be allowed to shoot it indoors (depends on range). Next cheapest is plated which is around (80-120) per 1k depending on brand and weight. Is cleaner than lead but you can't push it to extreme or the plating could be damaged causing bad accuracy. Of course next is fmj and you'd have to look prices up. Obviously fmj is the best bit generally most expensive.


As for bullet weights....that's up to you really. For 10mm I use either 180gr or 220gr plated bullets and havemt had an issue yet. But they do make different weights for different applications. I generally stick to the weight the gun was originally and is most commonly found in. Ie 115gr for 9mm, 230gr for 45acp ect. I do use other weights such as 147gr for subsonic 9mm for my suppressor. See bullet weight is hard to say which is best. Just go with what the gun was designed around or you have been shooting.


As for 5.7 reloading....I have no clue on it and haven't looked really. Last time I did I don't think anyone was really reloading for it.
velillen is offline  
Old January 10, 2013, 10:21 AM   #3
jmortimer
Junior member
 
Join Date: January 24, 2010
Location: South West Riverside County California
Posts: 2,763
It appears you do not have a manual or may not be using it. Get Modern Reloading if you do not have a manual, especially because you are using Lee Precision equipment. As for bullets go to a few bullet manufacturer sites or sellers like Mid-South and price them out. I use cast bullets which would be the least expensive, but probably not the best choice for you. Berry's plated bullets are a good deal. You got a good press to start out with.
jmortimer is offline  
Old January 10, 2013, 11:46 AM   #4
rg1
Senior Member
 
Join Date: November 6, 2001
Posts: 752
I'd check out this forum for loading 5.7x28 but this caliber is one that isn't best for reloading at all. Many issues with the laquer coated thin cases. Not for the inexperienced.
http://www.fivesevenforum.com/viewforum.php?f=19
rg1 is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 07:04 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.06547 seconds with 9 queries