The Firing Line Forums

Go Back   The Firing Line Forums > The Hide > The Art of the Rifle: Bolt, Lever, and Pump Action

Reply
 
Thread Tools
Old January 6, 2013, 06:43 PM   #1
jabraun98
Member
 
Join Date: October 28, 2012
Posts: 41
Surplus Ammo Question

I just picked up a case of surplus 7.62x54r for my mosin. Will ballistol clean the stuff that eats away at the bore?
jabraun98 is offline  
Old January 6, 2013, 07:01 PM   #2
Shadow7d
Member
 
Join Date: June 12, 2010
Location: Alaska
Posts: 42
WATER
this is a well beat topic BTW

hot soapy water
hot (cause it dries quicker)
soapy (gets the water under the fouling and oil)
water, cause it's the water that dissolves the corrosive salts and carries them away...
Shadow7d is offline  
Old January 6, 2013, 08:54 PM   #3
ToddG
Member
 
Join Date: June 29, 2012
Posts: 23
Generic Windex. Not the expensive stuff, the cheap knockoffs. I pour an inch or so into a plastic tub (like a butter tub), heat for a bit in the microwave, pull the bolt from the Mosin, muzzle down in the solution and drag a patch up and down, drawing the solution through the barrel. Pour a bit down the breach, use the patch to wide down, then patches to dry and light oil.

Or pony up for non-corrosive ammo.
ToddG is offline  
Old January 6, 2013, 08:59 PM   #4
Chowder
Senior Member
 
Join Date: July 3, 2012
Location: Anchorage, AK
Posts: 412
I don't own a mosin personally but my brother takes cheap windex to the range with him and when hes done sprays down the bore and chamber getting it nice and wet and runs a bore snake through it, repeats this a couple times and cleans like any other gun when he gets home. After a few years and a lot of shooting his bore still looks new.
Chowder is offline  
Old January 7, 2013, 12:40 PM   #5
Erno86
Senior Member
 
Join Date: September 22, 2012
Location: Marriottsville, Maryland
Posts: 510
Dunno much about Ballistol...but I cotton flannel patch out my bores {whether shooting corrosive/non-corrorsive ammo} with Simple Green solution, or a 1/3 mixture of: Simple Green, hydrogen peroxide and rubbing alcohol --- brush out the bore with your favorite copper cleaner --- flush out the copper cleaner with Hoppes #9 patches, dry patch out; then oil down.
Erno86 is offline  
Old January 7, 2013, 03:16 PM   #6
m&p45acp10+1
Senior Member
 
Join Date: May 3, 2009
Location: Central Texas
Posts: 3,307
Ballistol was made to clean out corrosive residue. It is water based. Though I still use water. I spray cheap ammonia down the chamber, and bore. Let it soak till I get home. I then spray some more, and wait a few minutes. I pour hot, as in hot from the tap hot water to flush it out with. Rinse one more time. I then run a few dry patches. Then clean like normal. The ammonia helps to get the copper fouling out as well. Lots of blue liquid, will come out of the barrel.
__________________
No matter how many times you do it and nothing happens it only takes something going wrong one time to kill you.
m&p45acp10+1 is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 05:29 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.06964 seconds with 9 queries