The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old January 3, 2013, 09:03 AM   #1
dnemeth51
Junior Member
 
Join Date: January 2, 2013
Posts: 3
Brass questions

Beginner here, I have some factory brass that were originally loaded with lead bullets, they have a grove in the case similar to the cannelure. I wondered if I could reload these cases with jacketed bullets or can they be reloaded at all??
dnemeth51 is offline  
Old January 3, 2013, 09:18 AM   #2
kimbers rule
Member
 
Join Date: November 3, 2012
Location: State of Jefferson
Posts: 95
That is the factory crimp groove. It wont hurt a thing to reload it the same way as anything else.
kimbers rule is offline  
Old January 3, 2013, 09:23 AM   #3
Magnum Wheel Man
Senior Member
 
Join Date: July 26, 2006
Location: Southern Minnesota
Posts: 8,355
I assume you are talking about the crimp "groove" which would have been under the base of the bullet, or crimped into a crimp groove below the case mouth??? depending on the cartridge ( 357 Magnum for example ) they may have been double crimped to help control bullet jump from recoil... I've reloaded 357 ( for example ) a couple times, & fire formed, & resized the bottom crimp out of the case after several reloadings ( they are definately reloadable, so long as they are brass & boxer primed ) I try not to buy those type of cases for reloading though, as it ends up being a weak point in case, & more often than not, that's the 1st place to crack
__________________
In life you either make dust or eat dust...
Magnum Wheel Man is offline  
Old January 3, 2013, 09:31 PM   #4
dnemeth51
Junior Member
 
Join Date: January 2, 2013
Posts: 3
They were 38 special, Im cheap and hate to throw stuff away, I have a bunch of diffrent jacketed bullets .357 cal and wanted to do something with the brass. Thank you for your answers, its nice to have some help considering that mistakes can be dangerious. Thanks again.
dnemeth51 is offline  
Old January 3, 2013, 09:58 PM   #5
Sport45
Senior Member
 
Join Date: May 25, 1999
Location: Too close to Houston
Posts: 4,070
They'll be fine as long as you don't seat the base of the bullet past the case cannelure.
__________________
Proud member of the NRA and Texas State Rifle Association. Registered and active voter.
Sport45 is offline  
Old January 3, 2013, 11:53 PM   #6
drail
Junior member
 
Join Date: February 2, 2008
Posts: 3,150
Use them. After they have been loaded and resized a few times there won't be much constriction left.
drail is offline  
Old January 4, 2013, 01:00 AM   #7
NWPilgrim
Senior Member
 
Join Date: September 29, 2008
Location: Oregon
Posts: 2,152
Once you resize it will seat a bullet properly like any other case. After you shoot it again you probably will not see that crimp line again or it will eventually disappear with firing and resizing.

Treat it like any other .38 case, it's fine. And that is a good reloader instinct to always research before throwing away. Actually, never throw away, at worst put into a recycle bucket to eventually sell as scrap. I put all my brass that has cracked, has loose primer pockets, any other defect, along with old brass pipe fittings, stripped brass screws, and anything brass.

But if you are inspecting brass and it has anything you know is wrong or close to it, just recycle it. I probably cull one or two cases every time I reload a batch of 100-200. Whether I recycle one or four cases is nothing in the long run and absolutely foolish to let those couple of marginal cases slip through. When it comes to defects my motto is, "If in doubt, recycle it!" If it is something I have not seen before and not sure if it is a defect then do what you just did, ask around and read up on it.
__________________
"The ultimate authority ... resides in the people alone. ... The advantage of being armed, which the Americans possess over the people of almost every other nation ... forms a barrier against the enterprises of ambition."
- James Madison

Last edited by NWPilgrim; January 4, 2013 at 01:07 AM.
NWPilgrim is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 01:33 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.05774 seconds with 7 queries