The Firing Line Forums

Go Back   The Firing Line Forums > The Hide > The Art of the Rifle: Bolt, Lever, and Pump Action

Reply
 
Thread Tools
Old January 5, 2013, 07:38 AM   #76
Bart B.
Senior Member
 
Join Date: February 15, 2009
Posts: 5,440
Some years ago, Ruger had problems with their receiver's not having barrel tenon axis well in line with their boltway. Other makes have sometimes had a receiver go out with the same problems.

Boresighting a bent barrel by looking through it then zeroing the sights on some down range point may not reveal its issue. Especially if it's only the last few inches of the bore that's bent. If the barrel is straight and both visual or muzzle-collimator boresighting ends up being way off from the scope's optical-mechanical axis, then the receiver's barrel tenon threads are crooked.

Note that putting a scope's adjustments at mid point in their range does not necessarily have them centered on the scope's optical-mechanical axis. That axis is typically off center of a scope's adjustment range. The only way to get a scope's reticule in line with its opto-mech axis, that is the center of the main tube front to back, is to put the scope in two fixed V blocks, one at each end of the tube, rotate the scope and make adjustments until the reticule center stays at the same place on the target as the scope's rotated through 360 degrees. That shows that as the scope's rotated, the image of the target where the reticule's centered doesn't move and therefore is exactly aligned with the scopes opto-mech axis. That axis is what the rings on the bases hold the scope at. And the amount of adjustment either side of that zero will typically be different both ways for both E and W knobs. Most folks are quite surprised at what they find out by doing this then checking the error between the bore axis and where the scope's axis is by boresighting.

So, check your mounted scope's alignment with the receiver with bases and rings attached only with the scope's adjustments set to the scope's true zero.
__________________
US Navy Distinguished Marksman Badge 153
Former US Navy & Palma Rifle Team Member
NRA High Power Master & Long Range High Master
NRA Smallbore Prone Master
Bart B. is online now  
Old January 5, 2013, 08:37 AM   #77
J2.
Senior Member
 
Join Date: June 12, 2008
Location: The Real America
Posts: 149
Forum: A place to get any and all possible answer, to any and all possible questions. Also a place to have an endless discussion on any and all topics.

Most of the Green-Horn dilemma could be eliminated simply by cancelling a cable subscription and reading a good book.

I'm no expert sniper or 1000 yrd shooter. I will never need to shoot more than a couple 100 yrds. I can hit what I need to on any given day. Experience with your gun is all you need and well thought questions will help you get there.
__________________
"Those who hammer their guns into plows will plow for those who do not."
J2. is offline  
Old January 5, 2013, 05:50 PM   #78
ak2323
Senior Member
 
Join Date: December 8, 2011
Location: Texas
Posts: 190
"I have to chuckle".

Whatever gets you through the day. Sounds like you're feeling a bit inferior and jealous of these noobs who buy high end equipment.
ak2323 is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 01:54 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.06608 seconds with 7 queries