The Firing Line Forums

Go Back   The Firing Line Forums > Hogan's Alley > Handguns: The Revolver Forum

Reply
 
Thread Tools
Old December 1, 2012, 06:03 PM   #1
saypek
Senior Member
 
Join Date: July 24, 2006
Posts: 200
Advice for my new revolver?

Just bought my first revolver, a taurus m85 steel frame. The plan is to make it my EDC after a few trips at the range, just to make sure i'm at least a decent shot with it. I was told to use standard pressure fmj loads for target practice. Question is, what ammo would you recommend for SD? Also, is it ok if i dryfire the gun w/ out snapcaps? I live outside the US and i cant seem to find any. Can i make improvised snap caps? I think i've become a revolver guy now. Im planning to sell my 1911 (my current hd gun) and replace it with a ruger or maybe s&w 4inch .357.
saypek is offline  
Old December 1, 2012, 06:40 PM   #2
old bear
Senior Member
 
Join Date: November 3, 2009
Location: Not close enough to the beach
Posts: 1,174
Your Taurus should be just fine with any 38 special ammo +P or not. If it makes you feel better shoot standard pressure ammo at the range, and load the hottest 38 special ammo you can legally get for self defense. In my Smith and Wesson M-60, J frame, I carry Federal 147Gr. +P+ ammo for self defense.
old bear is offline  
Old December 2, 2012, 03:38 AM   #3
Redhawk5.5+P+
Senior Member
 
Join Date: June 4, 2012
Location: NV
Posts: 743
I was told by someone that owns a M85 the manual stated not to dry fire.

I'd just take a little tiny piece of electrical tape and put it over the snap caps of pre shot shells.
Redhawk5.5+P+ is offline  
Old December 2, 2012, 03:52 AM   #4
Model12Win
Senior Member
 
Join Date: October 20, 2012
Posts: 781
As for the snap cap part, here are some!

http://www.cheaperthandirt.com/product/3-1019258

Not a bad price and you won't have to worry about damage if you use these.
Model12Win is offline  
Old December 3, 2012, 06:54 PM   #5
Redhawk5.5+P+
Senior Member
 
Join Date: June 4, 2012
Location: NV
Posts: 743
OP

Quote:
I live outside the US and i cant seem to find any. Can i make improvised snap caps? I
Canada? Some US companies send stuff outside of the US.
Redhawk5.5+P+ is offline  
Old December 4, 2012, 10:07 PM   #6
warnerwh
Senior Member
 
Join Date: February 11, 2009
Posts: 280
I have heard of people popping the primer out of a case and putting in silicone or using a rubber eraser for snap caps.
__________________
Portland, Or
warnerwh is offline  
Old December 5, 2012, 09:34 AM   #7
drail
Junior member
 
Join Date: February 2, 2008
Posts: 3,150
Homemade snap caps made by filling a primer hole with silicone or rubber will not cushion the firing pin. If you are convinced that you need snap caps buy some with spring loaded brass "primers" or just dry fire the gun empty. I have been dry firing S&W, Ruger, Charter and Taurus revolvers for 25 years without snap caps and never had any damage take place. The few times I have seen someone break a firing pin the pin was defective and using snap caps would not have made any difference. The pin was either over hardened or out of alignment. They would have broken with live rounds or snap caps. Limit the use of light bullet high velocity ammo in any revolver. 110-125 gr. high velocity ammo has damaged far more revolvers than dry firing without snap caps. 140 - 158 gr. loads are much easier on the gun.
drail is offline  
Old December 8, 2012, 12:19 AM   #8
bikerbill
Senior Member
 
Join Date: September 19, 2007
Location: Lago Vista TX
Posts: 2,377
An 85 was my first handgun, bought it probably 15 or more years ago ... still shoots like a champ, it's my car gun ... has never failed, no issues ... have fun
__________________
"If all guns were built with mechanisms that kept them from firing when held sideways, we could end gang violence." humorist Frank Fleming
bikerbill is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 03:54 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.09611 seconds with 7 queries