The Firing Line Forums

Go Back   The Firing Line Forums > The Conference Center > General Discussion Forum

Reply
 
Thread Tools
Old November 24, 2012, 11:05 PM   #1
rcase1234
Senior Member
 
Join Date: September 6, 2012
Posts: 246
Cleaning question

Hello everybody! The other day I had some trouble disassembling a firearm and luckily a friend was able to help me fully break it down. After cleaning all the components with Hoppes 9 with a q tip then drying it he instructed me to just reassemble the gun and I only oiled a few parts but I did not oil the trigger group and a few other parts. Is that wrong? I figured you would have to oil the trigger group but he told me it didn't matter. So now I'm worried about that part developing rust. Also I heard if you oil the gas system on an Autoloader shotgun then it will cause the gas system to gum up. Is this true?
rcase1234 is offline  
Old November 25, 2012, 12:29 AM   #2
BarryLee
Senior Member
 
Join Date: July 29, 2010
Location: The ATL (OTP)
Posts: 2,802
The best answer is to lube points as directed by the manufacturer of the specific firearm. There are some places that should not be lubed and other that definitely should be, but without more specifics I’m not sure anyone can offer specific advice.

If it were me I would start at the manufacture’s WEB site and see what information was available. Also, it might not hurt to spend some time with Google and search for specific information about you firearm.
__________________
A major source of objection to a free economy is precisely that it ... gives people what they want instead of what a particular group thinks they ought to want. Underlying most arguments against the free market is a lack of belief in freedom itself.
- Milton Friedman
BarryLee is offline  
Old November 25, 2012, 08:42 AM   #3
Arizona Smithshooter
Senior Member
 
Join Date: August 20, 2011
Location: Western Arizona
Posts: 167
Two things come to mind...Owners Manual and cleaning patches. Every Owner's Manual will tell you how to disassemble and clean your weapon. If you don't have a manual you can find a pdf version on the manufactures web site.

Cleaning patches are much better than Q-tips, which tend to leave fuzzy stuff all over your working internal parts. Pipe cleaners also work well to get into those hard to reach places and won't leave any fuzzy residue.
Arizona Smithshooter is offline  
Old November 25, 2012, 09:27 AM   #4
Warrior1256
Senior Member
 
Join Date: November 11, 2012
Location: Louisville, Ky.
Posts: 156
I have broken down and cleaned many firearms in my 56 years but I still depend on the owners manual. If it says oil it I do, if it dosen't say oil it I don't.
Warrior1256 is offline  
Old November 25, 2012, 09:43 AM   #5
Hawg
Senior Member
 
Join Date: September 8, 2007
Location: Mississippi
Posts: 11,872
The only trigger I don't oil is my Jewel because he specifically said not to. The rest I oil.
Hawg is offline  
Old November 25, 2012, 12:52 PM   #6
drail
Junior member
 
Join Date: February 2, 2008
Posts: 3,150
All of the moving parts need a little bit of oil. I'm talking a drop here and there. A little goes a long way. Just make sure NO oil gets on or can seep on to the breech face and wick into a primer. Keep that area dry.
drail is offline  
Old November 25, 2012, 04:04 PM   #7
kilimanjaro
Senior Member
 
Join Date: November 23, 2009
Posts: 2,013
Put a little oil on any moving parts and what they bear against. You can get instructions for your weapon online or by emailing the manufacturer, most of them will ship you a manual, free of charge, or have the information on their website. They don't want to be sued by someone who didn't have the instructions before the accident....
kilimanjaro is offline  
Old November 25, 2012, 04:47 PM   #8
mete
Senior Member
 
Join Date: June 14, 2004
Location: NY State
Posts: 5,491
Trouble dissassembling ? Why ?
I've been unable to dissassemble some guns where cheap oil had been used .This oil oxidized to a varnish requiring soaking in a strong solvent just to take apart .These guns must be thoroughly cleaned ,every part , including trigger ! Once cleaned they should be 'lightly' lubed with a very good gun oil all over .
If the manual gives specific instructions then follow those.
__________________
And Watson , bring your revolver !
mete is offline  
Old November 25, 2012, 11:14 PM   #9
rcase1234
Senior Member
 
Join Date: September 6, 2012
Posts: 246
I do realize this is a dumb question but when you say lube you mean oil right?
rcase1234 is offline  
Old November 25, 2012, 11:26 PM   #10
Edward429451
Junior member
 
Join Date: November 12, 2000
Location: Colorado Springs, Colorado
Posts: 9,494
moving parts need oil, but not enough to be able to collect dust & lint. What I do is after cleaning the moving parts and they are squeaky clean I put a drop of oil on them and spread it to cover the piece so it has a film all over it. It winds up sitting around for a short while while I am cleaning and oiling other parts etc., and at assembly I try to wipe the oil off with a clean cloth. This leaves oil in the pores of the metal and will be enough to protect against rust. The oiling points in the book for the specific weapon get another drop on assembly so as to be left wet with oil.
Edward429451 is offline  
Old November 28, 2012, 04:04 PM   #11
45Gunner
Senior Member
 
Join Date: August 8, 2009
Location: Boca Raton, FL
Posts: 1,737
If it can rust, put an extremely light coat of oil on it unless otherwise specified by the manufacturer/owner's manual.
__________________
45Gunner
May the Schwartz Be With You.
NRA Instructor
NRA Life Member
45Gunner is offline  
Old November 29, 2012, 12:27 AM   #12
BigRick
Member
 
Join Date: November 27, 2012
Posts: 22
Every metal part in my guns gets oil on it. Even if it's just wiped down with a oily rag. This includes the gas piston on my sks (it does get the lightest coat of oil though, a fairly dry rag with oil on it). Most get disassembled, cleaned, sprayed with oil then wiped with a rag and reassembled.
BigRick is offline  
Old November 29, 2012, 10:52 AM   #13
Pahoo
Senior Member
 
Join Date: February 16, 2006
Location: IOWA
Posts: 5,764
Too much lubricant Can hurt you !!!

Quote:
Is that wrong?
Well, you did not mention the firearm in question but generally, folks tend to use too much lube. Would have to give your friend, the benefit of the doubt. ..

Quote:
Also I heard if you oil the gas system on an Autoloader shotgun then it will cause the gas system to gum up. Is this true?
Depends on how long it's been since it was cleaned. There are some gun oils that gum up with time. Another problem is use in cold tempertures. I once had this happen on my 1100 as I could not pull the bolt back. After that, I actually had to switch to a dry lube, during deer season. ....

You really don't have much to worry about if you routinely inspect and clean your guns. I once had a friend bring his shotgun to me as he could not operate the top mount safety. Yep, it was rusted to the tope of the reciever. ..

Be Safe !!!
__________________
'Fundamental truths' are easy to recognize because they are verified daily through simple observation and thus, require no testing.
Pahoo is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 06:41 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.09344 seconds with 7 queries