The Firing Line Forums

Go Back   The Firing Line Forums > The Conference Center > General Discussion Forum

Reply
 
Thread Tools
Old November 24, 2012, 01:10 PM   #1
breakingcontact
Junior member
 
Join Date: October 25, 2012
Location: Austin, TX
Posts: 736
How much fitting are you willing to do on a new gun?

After spending several hours working on a Mossberg 930 SPX, I got to thinking about how frustrating it was, but the run around of sending it in would also be very frustrating and it might come back not fixed.

How much fitting are you willing to do on a new gun? When do you just ship it back to the manufacturer? When do you say to hell with it and sell it?

I could have just bought a Nordic mag extension like most guys are doing, but I wanted to make it work right with the parts it came with. It functions well now, but I have a mag tube that's been ground on and polished, a follower I had to clean up and now a forend that's all cut up to make it all fit right.

Achieved my goal, but wondering if I should have just spent the money and got the Nordic extension, sent it back to Mossberg or just not bought it at all.
breakingcontact is offline  
Old November 24, 2012, 02:10 PM   #2
alex0535
Senior Member
 
Join Date: November 4, 2012
Location: Georgia
Posts: 781
Not sure I know what you mean by "fitting". Parts in a good should generally fit together pretty well without doing anything to them.

I might sand down a wood stock to free float a barrel on a bolt action if it isn't already. I changed a trigger return spring in my Marlin 917v to give it a lighter pull.

I will take all of the internals out of a lever action rifle and polish them to remove machining burrs and other non smooth metal on parts of the gun that are metal to metal contact. Makes things much smoother.

I wouldn't keep a firearm that I could not rely on to not jam, misfire, or inexplicably not work at any given point. If something goes wrong I will take it apart, put it back together, and try again. If i couldn't figure out what was wrong I would try to find someone that could.
alex0535 is offline  
Old November 25, 2012, 01:21 AM   #3
johnwilliamson062
Senior Member
 
Join Date: May 16, 2008
Posts: 6,813
Dealing with the same problem on a 930. I am not messing with it. I am sending it back to them and they better send it back to me working. Any sort of function testing whatsoever would have found this problem at the factory and mine didn't even come with a front sight installed on the rifled barrel.
__________________
$0 of an NRA membership goes to legislative action or court battles. Not a dime. Only money contributed to the NRA-ILA or NRA-PVF. You could just donate to the Second Amendment Foundation
First Shotgun Thread First Rifle Thread First Pistol Thread
johnwilliamson062 is offline  
Old November 25, 2012, 06:19 AM   #4
Metal god
Senior Member
 
Join Date: April 10, 2012
Location: San Diego CA
Posts: 1,996
My Ruger American rifle has a free floated barrel . The barrel is free floating right out of the box ( did the dollar bill test ) The problem is , the stock is very cheap and the forend flexes when moderate presure is applied ( resting on a bag or bi-pod ).This causes the barrel to make contact with the stock and really hurts the accuracy by about 1 to 1-1/2 MOA. I ended up sanding the heck out of the barrel channel of the stock to give the barrel more room . It seemed to work and all is good now . I don't think you should have to do any work on a new firearm . The gun only cost $360 and I think it's clear were they saved some money . The gun is a sub MOA shooter so a little sanding is not that big a deal . If the gun cost double that like most nice bolt guns do I would have been PO . I would think A 6 or 7 hundred dollar shotgun should be good to go right out of the box . Lets hope you did not void your warranty by working on it .

I bought an AR that came from the factory with a very minor but potentially catastrophic problem with the FGC . All I needed to fix it was a $2 part and 5 min of my time . I chose to send it back for two reasons 1) I wanted them to know that they sent a firearm out with a real problem and 2) I did not want to void my life time warranty by putting in a after market part .

One gun cost almost 1k the other cost just over $300 . One got sent back the other did not . Its up to you to deside what your willing to tolerate and what the potential hazards could be .
__________________
As of this date 8-18-14 at 6:42am I became a proud grandfather I guess I'm officially old
Metal god is online now  
Old November 25, 2012, 09:41 AM   #5
Aguila Blanca
Senior Member
 
Join Date: September 25, 2008
Location: CONUS
Posts: 6,418
Quote:
Originally Posted by breakingcontact
How much fitting are you willing to do on a new gun?
None. A new gun should work ouit of the box. That's why I bought a new gun. If I wanted a project, I'd buy a box of parts.

Quote:
When do you just ship it back to the manufacturer?
When I see that it doesn't work, or doesn't fit correctly.

Quote:
When do you say to hell with it and sell it?
If the manufacturer doesn't make it right the first try. I don't have time to waste on defective products with no product support. If the people who make it can't fix it, why should I bother with it?
Aguila Blanca is offline  
Old November 30, 2012, 01:31 PM   #6
Smilin Jack
Senior Member
 
Join Date: December 31, 2009
Location: West Florida Republic
Posts: 131
I fit bullets in it.
I fit my finger to the trigger.
I fit holes in the paper.
Or I fit it in a box to go back.
If they can't fix it right the first time then I pitch a fit.
__________________
History will never record how many men have performed great deeds because they were driven out of their homes by some unbearable trait of their wives, from which they fled, almost joyfully, to face as an alternative peril and even death.
Major John Reid
Smilin Jack is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 10:12 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07089 seconds with 7 queries