The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Smithy

Reply
 
Thread Tools
Old November 30, 2012, 03:21 PM   #1
Buzzard Bait
Senior Member
 
Join Date: June 25, 2008
Location: Republic of Texas
Posts: 338
glossy finish to satin

Does anyone have any suggestions / experience with taking a glossy wood finish and making it a more satin type? I have refinished a stock using true oil it's very glossy and was wondering about what to use to break the gloss would roten stone be a good choice?
bb
Buzzard Bait is offline  
Old November 30, 2012, 06:31 PM   #2
PetahW
Senior Member
 
Join Date: September 19, 2008
Posts: 4,679
If you've properly filled the pores, the gloss coat can be gently rubbed down/off with a pad of OOOO steel wool, then waxed with a good paste wax, like Johnson's.


.
PetahW is offline  
Old November 30, 2012, 10:43 PM   #3
wyop
Senior Member
 
Join Date: July 15, 2012
Location: Wonderful, Windy Wyoming
Posts: 133
4/0 steel wool, applied lightly. If your finish isn't filled, I'd recommend against using steel wool and instead look at using a very fine grade of wet/dry (like 1200 or finer) paper.

There are some buffing compounds that can also take the sheen off a high-gloss finish. Look in Brownells.
wyop is offline  
Old December 1, 2012, 04:02 AM   #4
Scorch
Senior Member
 
Join Date: February 13, 2006
Location: Washington state
Posts: 11,476
Rotten stone is the material of choice for deglossing wood finishes. It will make even a hard finish lose its gloss pretty fast without wearing through the finish. You can get it from Brownells or from your local art supply store or woodworking store.
__________________
Never try to educate someone who resists knowledge at all costs.
But what do I know?
Summit Arms Services
Taylor Machine
Scorch is offline  
Old December 1, 2012, 08:52 AM   #5
Bailey Boat
Junior member
 
Join Date: December 10, 2006
Location: NC
Posts: 365
I've had good success using white polishing compound. The finest that you can find. IF you have access to 3M "Finessit" that is even better due to it's consistancy. Finessit is a 3000+ grit polishing compound intended to remove scratches from clear coat of autos and boats. I usually buy a small amount from a body shop.....
Bailey Boat is offline  
Old December 1, 2012, 07:36 PM   #6
oneoldsap
Senior Member
 
Join Date: September 16, 2009
Location: I live in the foot of the Green Mountains of Vermont
Posts: 1,588
I just scuff up the surface and spray with with Min-Wax Satin Spar Urethane ! Two or three light coats should do the trick . When I say light I mean just looking wet . You may want to mask your checkering , till you apply the last coat . It's rugged stuff , UV resistant , and easy to touch up if you have a mishap !
oneoldsap is offline  
Old December 1, 2012, 08:58 PM   #7
Bob Wright
Senior Member
 
Join Date: July 10, 2012
Location: Memphis, Tennessee
Posts: 1,897
Birchwood Casey makes a stock conditioner especially for this purpose.

Bob Wright
Bob Wright is offline  
Old December 2, 2012, 08:44 AM   #8
Rifleman1776
Senior Member
 
Join Date: April 25, 2010
Location: Arkansas
Posts: 3,309
I'm a four aught steel wool guy. As long the original plastic finish has been removed first.
Rifleman1776 is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 06:34 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07590 seconds with 9 queries