The Firing Line Forums

Go Back   The Firing Line Forums > Hogan's Alley > Handguns: The Semi-automatic Forum

Reply
 
Thread Tools
Old November 6, 2012, 10:44 PM   #1
AdamSean
Senior Member
 
Join Date: November 18, 2007
Location: Tuscaloosa, AL
Posts: 445
Potential problem or just needs to be worked in?

Ok, I just picked up a new pistol this week. It doesn't matter what kind it is, but I will tell you its a Sig Sauer SP2022 9mm. I have not taken it out to shoot yet, but I did clean it from all the sticky grease they package them with and lubed it up. While I was handling it, I noticed something I have never noticed before on any pistol. If you press the front of the slide back about a quarter of an inch to do a brass check and lightly release, the slide will not go back into full battery. But if you press the rear of the slide just a bit it goes back into full battery.

Now this does not happen when the takedown pin is removed, but only when it is inserted. I am wondering if this just means I need to take the gun out and shoot it a few hundred times to smooth everything out. I have noticed that my Glocks are quite stiff until I get about 500 or 600 rounds through them then they are nice and smooth.

This is what it should look like.


This is me pressing it back.


And this is what happens when you release. Notice the guide rod protruding a little.
AdamSean is offline  
Old November 6, 2012, 10:59 PM   #2
Rob228
Senior Member
 
Join Date: May 29, 2010
Location: Broomfield CO
Posts: 568
I've always been in the habit of giving the rear of the slide a bump with the heel of my palm after doing a brass check.
Rob228 is offline  
Old November 7, 2012, 12:33 AM   #3
RsqVet
Senior Member
 
Join Date: February 20, 2005
Posts: 2,338
It should not do what you are describing, are you press Checking with an empty mag in the gun so the slide stop is causing increased resistance? Only thing I could think that might induce what you describe.

I would put a few 100 down range and see if it resolves, I suspect it will.
RsqVet is offline  
Old November 7, 2012, 10:38 AM   #4
chris in va
Senior Member
 
Join Date: December 26, 2004
Location: Louisville KY
Posts: 12,513
This is typically the test with Glocks to find out if the mainspring is worn out.

However in your case it's just new and needs to be 'warmed up'. My friend bought a new 229 a few years ago and it had numerous FTF issues until about the 400rd mark.
chris in va is offline  
Old November 7, 2012, 08:11 PM   #5
AdamSean
Senior Member
 
Join Date: November 18, 2007
Location: Tuscaloosa, AL
Posts: 445
I tried the same with the display at the store and it does not do it. But then again the displays have been brass checked and cycled hundreds of times. I have been cycling the slide while watching TV and it seems to be getting better.
AdamSean is offline  
Old November 7, 2012, 08:37 PM   #6
Sport45
Senior Member
 
Join Date: May 25, 1999
Location: Too close to Houston
Posts: 4,053
What did you use to lube the rails?

I'll admit to running my guns pretty wet, but yours looks absolutely dry.
__________________
Proud member of the NRA and Texas State Rifle Association. Registered and active voter.
Sport45 is offline  
Old November 7, 2012, 11:10 PM   #7
DPris
Senior Member
 
Join Date: August 19, 2004
Posts: 4,526
Go shoot it.
Denis
DPris is online now  
Old November 7, 2012, 11:17 PM   #8
chadk7
Senior Member
 
Join Date: December 9, 2010
Location: indiana
Posts: 210
My Sig p250c wouldnt go all the way into battery when I first got it either. If I pulled the slide back just a little or if I rode the slide forward instead of just slingshotting it, it wouldnt go all the way forward. It went away after I shot it a few times though. I would try a few range sessions and see if it improves.

Sent from my PC36100 using Tapatalk 2
chadk7 is online now  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 03:22 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.08592 seconds with 9 queries