The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old November 9, 2012, 11:58 AM   #26
10 Spot Terminator
Senior Member
 
Join Date: January 3, 2008
Location: Central Oregon
Posts: 348
For my 300 Win. Mag Browning A-Bolt with a 26 inch barrel

This rifle I nearly gave up on due to a short magazine issue that was keeping me away from being able to seat bullets to published coal specs and accuracy was only being achieved by "single loading" due to excess bullet jump to the lands if cartridges were seated to fit the magazine. A Barnes TSX bullet solved this for me due to the "long jump" preference of these bullets.

73.0 gr. IMR4350 ( .5 gr. under max per Barnes , see footnote at bottom )
Federal 215M primer
Federal Premium case ( nickle )
3.365 coal with moderate Lee crimp using FCD die
3,225 fps chronographed with 13 fps standard deviation
sub MOA @ 200 yds. ( just barely )

Load data for the Barnes "grooved" bullets tend to have higher max load limits than loads published for other "non grooved" bullets by such as Hodgdon as the "grooved" bullets tend to create lower pressures due to a reduced amount of load bearing surface contact between the bullet and the bore.

A Lee factory crimp die was used with a moderate pressure as the bullet coal is 0.015 in. less than the inside dimension of the magazine. No feeding problems have occured and none are wanted therefore we crimp.

This load I have nick named "Thors' Hammer" as it anchors deer and elk . The Barnes is without a doubt one "MAJOR BAD BOY" in terminal performance !
10 Spot Terminator is offline  
Old November 9, 2012, 12:54 PM   #27
rclark
Senior Member
 
Join Date: February 12, 2009
Location: Butte, MT
Posts: 1,689
.357 mag : 5.0g Red Dot under 158g SWC.

.44Spec : 7.5g Unique/Universal under 240g SWC (works very well in all my specials)
Note : The above Skeeter load is NOT for use in .44Spec CA Bulldog

.44Mag : 10.0g Unique under 240g SWC (works very well in both my .44Mags)

still working on .45 Colt favorite loads but over the last few years :
.45Colt : 20.0g of IMR 4227 under 255g SWC (mag CCI primer)
.45Colt : 7.0g Green Dot under 250g RNFP

.45ACP : 5.0g Bullseye under 200g TC
Note : I've only shot this in revolvers as I don't have a slab-sides pistol.

As mentioned above ... this work fine in my guns. YMMV. Always double check before using loads found on-line.
__________________
A clinger. When guns are outlawed, only outlaws will have guns. Single Action .45 Colt (Sometimes improperly referred to by its alias as the .45 'Long' Colt or .45LC). Don't leave home without it. Ok.... the .44Spec is growing on me ... but the .45 Colt is still king.

Last edited by rclark; November 9, 2012 at 01:02 PM.
rclark is offline  
Old November 9, 2012, 01:12 PM   #28
Old Grump
Member in memoriam
 
Join Date: April 9, 2009
Location: Blue River Wisconsin, in
Posts: 3,144
Only sharing two, My 45 likes 4.6 gr of bullseye behind a 230 gr LSWC. My .308 isn't as fussy but I do really well with 43.6 gr of 4350 behind 180 gr Core-lokt bullets. I could load it hotter but 1 1/2 at 200 yards is good enough for me, I can't shoot any better than that no matter what load I used.
__________________
Good intentions will always be pleaded for any assumption of power. The Constitution was made to guard the people against the dangers of good intentions. There are men in all ages who mean to govern will, but they mean to govern. They promise to be good masters, but they mean to be masters.
--Daniel Webster--
Old Grump is offline  
Old November 9, 2012, 01:30 PM   #29
RC20
Senior Member
 
Join Date: April 10, 2008
Location: Alaska
Posts: 2,141
Quote:
On the other hand, it's undeniable that carefully crafted ammo will almost always be better than generic factory ammo. Still though, carefully crafted ammo that is specific to a guns twist rate and free-bore will probably be better than carefully crafted ammo that's NOT tailored to the gun, if the gun is as I mentioned chambered in a cartridge which has a less standardized setup.
__________________
I had a 7mm that a not only carefully crafted, checked the free bore and set it tighter than factory did.

Ok, but it never shot all that well (1.5 at 100)

One day I was headed out for a hunt way up North and it was "oh ****, no rounds loaded up". Screw it, down to the store, Federal Premium on sale in the right gr bullet, down to the range.

Damn, these things shoot better than my hand-loads!.

After that, I just bought them. Sometimes for the mission it just doesn't pay (and yes I am still reloading, I like it and get better resutls mostly, but for that once a year hunt where it doesn't matter than much between 3/4 MOA and 2 inches, factory is fine!
RC20 is offline  
Old November 14, 2012, 12:01 AM   #30
crowbeaner
Senior Member
 
Join Date: June 4, 2007
Location: Upstate SC
Posts: 1,943
222 Rem: WW brass, match prepped, RP 7 1/2, 21.0 of RL7, Speer 50 grain sp, 2.130"
222 Rem, brass the same, CCI 400, 24.0 of BLC2, Speer 52 grain original HP, 2.130"
270 Win, WW brass, 52.0 of H414/WW760, WLR primer, 130 Hornady Interlock, light crimp in cannelure
30/06; WW brass, CCI 200, 54.0 of H414/WW760, RP 150 SPCL, light crimp in cannelure
30/06; brass the same, same primer, 52.5 of H414/WW760, Hornady 165 Interlock flatbase
30/06; RP brass, RP 9 1/2, 47.0 of IMR 4320, Hornady 165 BTSP
30/06; RP brass, RP 9 1/2, 47.0 of IMR 4064, Hornady 180 BTSP
300 Win Mag (long version) FC brass, CCI 200, 67.5 of H414/WW 760, Hornady 165 BTSP--- max load
__________________
If you want your children to follow in your footsteps, be careful where you walk.
Beware the man that only owns one gun; he probably knows how to use it.
I just hope my ship comes in before my dock rots.
crowbeaner is offline  
Old November 14, 2012, 10:24 AM   #31
DASHZNT
Junior member
 
Join Date: July 13, 2012
Posts: 179
For Handguns, Ive had great sucess with the .45ACP 230gr RN @ 4.5gr of Alliant Bullseye with a CCI #300 primer and an OAL of 1.265". Theyve been very accurate and consistant.

For Rifles, I havent made anything beyond .223/5.56NATO. I have had great success with this round. Specifically, I use a 62gr M855 FMJ-SC @ 25.0gr of Hodgdon H4895 with a CCI #450 and an OAL of 2.255". This load has worked wonders for me. Its surgically accurate and devastating if youre on the receiving end of it!!

Hope this helps anyone, if there is something you can share with me to improve these loads, Or maybe share a load that Im planning on getting into, Im all ears!!

DASHZNT
DASHZNT is offline  
Old November 14, 2012, 07:01 PM   #32
FM12
Senior Member
 
Join Date: February 5, 2007
Location: Monroeville, Alabama
Posts: 1,606
185 grain JHP in 45 auto with a bunch of Unique. (too much to mention here)
FM12 is offline  
Old November 14, 2012, 07:12 PM   #33
Rebel9793
Senior Member
 
Join Date: October 11, 2012
Location: Florida
Posts: 134
Savage .223 1:9 twist
winchester brass
CCI #400 small rifle primers
26gr Varget
55gr V-max with canterlure
Rebel9793 is offline  
Old November 14, 2012, 08:34 PM   #34
603Country
Senior Member
 
Join Date: January 6, 2011
Location: Thornton, Texas
Posts: 2,364
My 220 Swift favorite load didn't come from my experimentation. An article from a Shooter's Digest from the 1970's said that there was never a 220 Swift that didn't like 38.5 grains of IMR 4064 behind a 55 grain bullet. Hmmm...so I got out my reloading stuff and worked up to that load and that is the load that I have used since then. Yessiree...that is a good load.

For the 270, my long time favorite is 59 grains of 4831sc behind a 130 gr Nosler Ballistic Tip.

CCI BR primers in both of the loads above. Work up to both loads since they are near max (depends on the loading book you are reading).
603Country is offline  
Old December 23, 2012, 09:17 AM   #35
Turbo6ta
Member
 
Join Date: October 9, 2012
Location: SW Florida
Posts: 27
QUOTE: Nevmavrick

About 3/4 of the Internet is cussing because they've run into the small-primer .45s. Am I to understand you've chosen to seek them out and load them as the usual case?
________________________________

I don't see anything at all wrong with small pistol primers (at least when used in the .45 ACP)

I needed some more once-fired .45 ACP brass, so it just happens that they were all small primer, but at a very good price. So, I bought the brass and the Winchester small primers ... The primers were no harder to insert than the large, and never a misfire from them.

I think they fire cleaner too than the large primers. Anyway, that's all I use now, and it won't be long until small primers is about all your going to see.

Ron,
Turbo6ta is offline  
Old December 23, 2012, 02:26 PM   #36
Sevens
Senior Member
 
Join Date: July 28, 2007
Location: Central Ohio
Posts: 9,177
Ron, the problem isn't that small primer .45 brass doesn't work, or doesn't work well. It runs GREAT, I use them also. The problem is that we literally have one HUNDRED years of brass before some idiot knucklehead decided to make a change.

At the least, it's an annoyance. In reality, it gets to be dangerous when a piece of small primer .45 gets mixed in with your large primer .45 and you attempt to prime it, especially for those working with progressive machines or volume operations.

Certainly, you can make the argument that they need to be on their toes and inspect their brass, but someone has still created a problem out of nowhere.

Quote:
it won't be long until small primers is about all your going to see.
Not hardly. I found some .357 Magnum brass on my last range trip with the Super-Vel headstamp. Quick search suggest this stuff was last marketed in 1974. I've found plenty of large primer .45 Auto milsurp brass with head stamps dating to the 1950s. The truth is that both you and I will have gone to our final resting place before handloaders stop coming across large primer .45 Auto brass.

The idea to make it small primer certainly benefits things from a production standpoint, no need to argue otherwise as it's fact. From a handloader's standpoint, it's absolutely awful idea. It'd be a fine idea if you had the benefit of a time machine or the ability to re-write history.

They should have left .45 alone and changed 10mm Auto to small primer...that I could get on board with!
__________________
Attention Brass rats and other reloaders: I really need .327 Federal Magnum brass, no lot size too small. Tell me what caliber you need and I'll see what I have to swap. PM me and we'll discuss.
Sevens is offline  
Old December 23, 2012, 05:45 PM   #37
Colorado308shooter
Member
 
Join Date: November 11, 2012
Posts: 72
I load 4 calibers, this is what works in my guns:

9mm......4.5 grains Universal behind a 124 grain Berry's bullet, very accurate. Ruger SR9-C

40 S&W......6.7 grains Longshot behind a 180 grain Berry's, mild recoil and accurate. Springfield XD-40 4" barrel.

223......25.3 grains H4895, Hornady 55 grain FMJBT, CCI 400 primer, Rem case....consistently shoots 1.5"-2" at 100 yards, 5 shots from a Mini-14. With A-Max bullets, I can get it down to an inch at 100 yards.

308....44.5 grains IMR-4895, CCI 200 primer, Rem case, Nosler 168 grain HPBT....this load will consistently shoot an inch at 100 yards, 5 shots. This is from a Remmy 700 SPS Tactical with 20" heavy barrel. About 1 out of 4 groups will print 3/4" inch....I'm happy with this.
Colorado308shooter is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 02:27 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.09809 seconds with 7 queries