The Firing Line Forums

Go Back   The Firing Line Forums > The Hide > The Art of the Rifle: Bolt, Lever, and Pump Action

Reply
 
Thread Tools
Old November 8, 2012, 09:08 PM   #1
crowsing
Member
 
Join Date: November 7, 2012
Location: Boerne texas
Posts: 20
cutting down synthetic

can u cut down synthetic stocks. i cant get a yes or no answer. my thought is if u cut off and there is nothing to screw your recoil pad into you can fill it with an epoxy resin and tap it for screw holes. Or u could fill it w a light weight balsa wood and epoxy that in. any thoughts?
crowsing is offline  
Old November 8, 2012, 09:16 PM   #2
Scorch
Senior Member
 
Join Date: February 13, 2006
Location: Washington state
Posts: 11,449
Depends entirely on the stock. In general, yes, nut not always. And how you mount a pad varies from easy to impossible.
__________________
Never try to educate someone who resists knowledge at all costs.
But what do I know?
Summit Arms Services
Taylor Machine
Scorch is offline  
Old November 9, 2012, 03:34 PM   #3
jmr40
Senior Member
 
Join Date: June 15, 2008
Location: Georgia
Posts: 5,947
I've not ran across any that couldn't be cut down. Putting the pad back on is the only trick with some. Most of the better stocks are designed with enough extra material to allow for a certain amount of cutting. The cheaper tupperware stocks are really not designed to do so. But a block of wood cut to a tight fit and epoxied into the end gives something to screw into.

Filling the hollow stock with expanding foam, letting it harden and cutting excess off will give a flat surface where the pad can be epoxied directly to the stock. Cutting a $1.99 flip flop to the correct size and gluing it on works great BTW. Saves a lot of money and weight. The last one I did weighed 1/2 oz vs 5 oz for a standard pad and cost under $2.
jmr40 is offline  
Old November 10, 2012, 01:18 AM   #4
hoghunting
Senior Member
 
Join Date: March 27, 2006
Posts: 1,346
Or you could do the same thing as my Mcmillan stock and epoxy the pad to the stock.
hoghunting is offline  
Old November 10, 2012, 09:33 AM   #5
taylorce1
Senior Member
 
Join Date: November 18, 2005
Location: On the Santa Fe Trail
Posts: 5,456
I had a cheap Steven's 200 cut down to fit my daughter. I was wondering how the GS did it so I pulled the pad off. He epoxied a piece of plywood inside the stock that fit perfectly into the opening, and gave a solid surface to attach the pad to. Good thing was he only charged me $100 including the pad.
__________________
NRA Life Member
The Truth About Guns
taylorce1 is offline  
Old November 11, 2012, 04:44 PM   #6
Picher
Senior Member
 
Join Date: December 14, 2004
Location: Maine
Posts: 2,781
I cut down a Rem #7 and had enough material left to re-attach the original pad with screws.
Picher is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 10:16 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07657 seconds with 9 queries