The Firing Line Forums

Go Back   The Firing Line Forums > The Hide > The Dave McCracken Memorial Shotgun Forum

Reply
 
Thread Tools
Old November 19, 2010, 05:26 PM   #1
RMC51
Member
 
Join Date: December 29, 2008
Location: Florida Keys
Posts: 85
Winchester 1200 stainless. rare

I am looking for something very rare.
I have a Winchester 1200 Police, 1982, They are Stainless and factory chromed, it has a 18.5 inch barrel. I would like to find a 28-30 inch barrel for this thing. What I am looking for may not exist???. Who are the experts on old winchester shotguns that could help with good info.

RMC
RMC51 is offline  
Old November 20, 2010, 10:26 AM   #2
PetahW
Senior Member
 
Join Date: September 19, 2008
Posts: 4,679
Yep - About as rare as snake feathers.

AFAIK, you will have to obtain a blued Model 1200 barrel in the longer length & have it nickel-plated/chromed, since IIRC Winchester never made a longer stainless/etc M1200 bbl.

Google "shotgun barrels" for places like BarrelExchange.com, Corsons.com, & others, for sources.

.
PetahW is offline  
Old November 20, 2010, 01:37 PM   #3
jmr40
Senior Member
 
Join Date: June 15, 2008
Location: Georgia
Posts: 5,959
Are you sure it's stainless and not satin nickle? Winchester receivers were made from aluminum alloy, not steel. I would think that if they were going to going to go to the trouble to make a few stainless shotguns it would be more cost effective to make a bunch.

Not saying it isn't SS. But the Ruger Red Label is the only stainless shotgun I'm aware of. Several companies have made satin nickle plated shotguns.
jmr40 is offline  
Old November 20, 2010, 07:47 PM   #4
JNewell
Senior Member
 
Join Date: March 12, 2000
Posts: 1,092
I have seen short stainless barrels. AFAIK there was never a "sporting" length stainless barrel. As mentioned above, the receiver was always aluminum, sometimes plated (which was the case with the stainless "marine" models). IIRC, the plated marine models held up better than the stainless-barrel version - go figger. You could get a longer barrel plated, or there's probably a DuraCoat product that would closely match.
JNewell is offline  
Old November 20, 2010, 08:28 PM   #5
jaguarxk120
Senior Member
 
Join Date: February 28, 2008
Location: Michigan
Posts: 1,947
Winchester made a polished reciever model for export. The sides were not colored black but had a high polish. And it was aluminum alloy.
jaguarxk120 is offline  
Old November 20, 2010, 09:30 PM   #6
Dfariswheel
Senior Member
 
Join Date: May 4, 2001
Posts: 6,825
Winchester did make Model 1200 shotguns with stainless steel barrels and possibly other parts.
This was sold as the Winchester Model 1200 Police Stainless.
It was made in an 18" barrel with a 7 shot magazine.

Strangely, Winchester said that the stainless barrels tended to rust inside easier than the plated guns, so they discontinued the stainless steel barrels and went to all plated guns in the Model 1300 Marine Defender.
Dfariswheel is offline  
Old November 21, 2010, 12:37 AM   #7
RMC51
Member
 
Join Date: December 29, 2008
Location: Florida Keys
Posts: 85
Factory info

check old post for the info I got from Winchester and pictures
http://thefiringline.com/forums/show...37&postcount=1

http://thefiringline.com/forums/show...0&postcount=13

I'm going to buy another 12ga that has a 28-30" barrel
RMC51 is offline  
Old November 23, 2010, 02:39 PM   #8
musicmatty
Senior Member
 
Join Date: September 30, 2009
Location: Eastcoast
Posts: 140
I recently spotted a used one of these in a gun shop..it has a wood stock and front end with chromed everything else and a very short barrel. . The shop was selling this used shotgun for just under $600. Seems like a bit to much for a used pump action Winchester??

Any thoughts on this?
musicmatty is offline  
Old March 18, 2013, 11:50 AM   #9
sooftwn12
Junior Member
 
Join Date: October 10, 2009
Posts: 2
Winchester 1200 Marine

There is a Winchester 1200 "Marine" I purchased one New in 1979 or 1980 at Gart Brothers in Aurora, Co. It has a Stainless 18 1/2" bbl, plus magazine tube. and various fittings. Holds 6+1 3" or 7+1 23/4". It has rifle sights front and rear(adjustable). Currently fitted with a Burris FASTFIRE holo sight. With Fedral 23/4 Slugs, will print 7" @ 100 yards. Hope this settle some arguements..
sooftwn12 is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 11:32 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07458 seconds with 9 queries