The Firing Line Forums

Go Back   The Firing Line Forums > The Hide > The Art of the Rifle: General

Reply
 
Thread Tools
Old November 29, 2012, 01:54 AM   #1
GunXpatriot
Senior Member
 
Join Date: November 28, 2011
Location: New York
Posts: 318
Rusty barrel crown: A Big Problem?

So I was cleaning my guns from the previous range trip, including the range trip before that. I had put off cleaning my Marlin 795 for a while, and now that I've cleaned it, I realized there was rust on the muzzle crown! it was located between where the rifling ends and the "outside rim" of the crown. I took some break free and a few paper towels and "buffed" it out with my finger. There is still some left. Should i be worried about accuracy? The actual edge where the rifling ends is completely undamaged. I feel like it got this way because at that last range trip, the air conditioner didnt work and it was about 92 degrees out. I rapid-fired the hell out of the thing and put it back in the case when it was pretty hot. Even after all this time, when I opened the gun case, I could literally feel humidity escape... So. Will this be a big deal?
GunXpatriot is offline  
Old November 29, 2012, 08:44 AM   #2
.22lr
Senior Member
 
Join Date: July 14, 2007
Posts: 239
Shoot it.

If your accuracy is degraded, recrown the barrel.

If not, continue merrily.

Happy holidays.

`Matt
.22lr is offline  
Old November 30, 2012, 04:05 PM   #3
warbirdlover
Senior Member
 
Join Date: December 13, 2009
Location: central Wisconsin
Posts: 2,324
What .22lr said but there are some rust removing compounds that I would try. Get the rust off and then put some oil on it.

http://www.amazon.com/KRUD-KUTTER-RG...s=rust+remover
warbirdlover is offline  
Old November 30, 2012, 04:27 PM   #4
Bill DeShivs
Senior Member
 
Join Date: April 7, 2006
Posts: 7,166
Take a small wad of 0000 steel wool, and very gently scrub it in a circular motion with your thumb until the remaining rust is gone. Make sure you clean the residual steel wool from the bore and action. You might plug the bore with a patch or piece of tissue first.
The chemical rust removers will remove the bluing-the steel wool won't.
__________________
Bill DeShivs
www.billdeshivs.com
Bill DeShivs is offline  
Old November 30, 2012, 07:37 PM   #5
James K
Staff
 
Join Date: March 17, 1999
Posts: 19,837
The critical point is "where the rifling ends". That point must be even or the bullet comes out of the barrel unevenly and accuracy goes to heck.

As for anywhere else, there is no effect. There is no way rust between the hole in the barrel and the outside of the crown could affect anything.

Jim
__________________
Jim K
James K is offline  
Old December 15, 2012, 09:19 PM   #6
publius
Senior Member
 
Join Date: January 25, 2005
Location: Mississippi/Texas
Posts: 2,457
Always heed Bill's advice, he knows his stuff.
__________________
"Suppose you were an idiot, and suppose you were a member of Congress, but I repeat myself." Mark Twain
publius is offline  
Reply

Tags
barrel , crown , rust

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 07:31 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07738 seconds with 9 queries