The Firing Line Forums

Go Back   The Firing Line Forums > The Hide > The Dave McCracken Memorial Shotgun Forum

Reply
 
Thread Tools
Old September 26, 2012, 12:19 AM   #1
Sphawley
Senior Member
 
Join Date: June 9, 2010
Location: Las Vegas
Posts: 272
10 Gauge Shotgun Loads

Just picked up my first 10 gauge, and I want to start reolaoding for it...

However I do not want to have to buy a new press or conversion kit to relaod for the 10. What are my other options? Are there other options?

Im not looking at doing a lot of reloading for the 10 at this point in time but would like to be making my own shells.

What about going with brass shells? I have no experience with this, worth the trouble? What are their pros and cons?
__________________
If guns kill people, then pencils misspell words, cars make people drive drunk, and spoons made Rosie O' Donnell fat!

Last edited by Sphawley; September 26, 2012 at 12:35 AM.
Sphawley is offline  
Old September 26, 2012, 12:48 AM   #2
Virginian-in-LA
Senior Member
 
Join Date: February 11, 2012
Location: Evangeline, LA
Posts: 746
Without a press or conversion kit, how do you propose to reload? What am I missing?
I would also suggest you get Ballistic Products reloading catalog.
Virginian-in-LA is offline  
Old September 26, 2012, 05:23 AM   #3
darkgael
Senior Member
 
Join Date: February 9, 2006
Location: Homes in Brooklyn, NY and in Pennsylvania.
Posts: 4,296
reload

Reload without a press? Yes, you can do it. The quality of the shells will be a function of how meticulous you are....and reloading will be slow.
Without proper equipment, you will not be able to resize the hulls. That may not be a problem at all, especially since you have a single gun in ten gauge.
You can deprime the hulls with a nail or punch. Place the base of the hull over a hole in a piece of wood...a hole large enough to accept a 209 primer or two. Knock the primer out with the punch and a mallet.
Reprime - get a flat, clean piece of steel, hard plastic or marble. Put a 209 primer that is appropriate for your load (check a manual) on the flat surface, place a deprimed hull onto the primer, put some sort of rigid tube - aluminum or PVC, about 1/2" diameter and four to six inches long into the hull and gently tap the hull onto the primer with a mallet. Do not use a solid rod or dowel for this.
Measure the appropriate powder charge (check a manual for powder type and charge weight) - you will need a scale - and drop it into the hull. Place the appropriate wad (check a manual) into the hull atop the powder charge. This may be difficult as the crimp will be in the way. I used a piece of dowel sanded into a cone as a way of opening the old crimp folds. insert the wad with a dowel. Firmly. Measure and drop your shot load (check a manual). You will need a shot dipper for this.
The hard part is the crimp.
If you don't want to load the hull more than once, you can cut the old crimp folds off and glue in an overshot wad. Results may be iffy.
You could, with a bit of work, refold the old crimp, and reset it with an appropriately sized dowel - best to fit the hul inside a tube for that operation. VERY slow.
You could buy a roll crimp tool for use in a drill and roll crimp the hulls. This last is by far the best option. The issue to deal with when roll crimping is the old crimp folds.....They may prevent proper rolling. They can be cut off completely or partially, thus shortening the hull a bit or the folds can be spun out using a crimp doctor tool (a cone shaped item that fits into a drill chuck and is spun into the mouth of the hull; friction heats the crimp folds and relaxes them. With care, this works.)
This is one set of ideas...I have done this with 12 gauge hulls. They worked....but not as uniformly well as what I reload on my presses.
Pete
__________________
"Only hunting and mountain climbing are sports. The rest are just games." - R.Ruark
NRA Life Member

Last edited by darkgael; September 26, 2012 at 05:34 AM.
darkgael is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 01:29 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.08376 seconds with 9 queries