The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old September 14, 2012, 12:07 PM   #1
muleyboy
Junior Member
 
Join Date: September 14, 2012
Location: Tollhouse California
Posts: 3
Noob question

Sorry if this is a repeat question but I couldn't find the right question in the forum history. I just started reloading for my .223 and things were going good until I got a case stuck. I pulled out the primer removal pin in fear that I might hit it with the drill bit...well I got the case out and put it back together and started FL sizing again. After a few cases I inspected one and noticed a bulge in the case where the neck meets the shoulder and it kinda looks like the mouth is smaller then the cases that I resized before the case got stuck! Any ideas on what I screwed up?

Last edited by Brian Pfleuger; September 14, 2012 at 01:08 PM.
muleyboy is offline  
Old September 14, 2012, 01:57 PM   #2
TheNatureBoy
Senior Member
 
Join Date: September 6, 2007
Posts: 1,181
A bulge in the case or an indention? If its an indention it could be the result of too much case lube. Case mouth smaller? Did you set the die again after putting it back together? Thinking out loud
TheNatureBoy is offline  
Old September 14, 2012, 04:04 PM   #3
muleyboy
Junior Member
 
Join Date: September 14, 2012
Location: Tollhouse California
Posts: 3
Im gonna try to post a picture of it, but need to figure out how to post pics...its a bulge cause I tried putting one of the cases in my AR and the bolt wouldn't go all the way forward...Im using the least amount of case lube as I can...its hard to actually see the lube on the case. Is there a certain distance the de-capper pin needs to be in the die? Could it be that I need to lube inside the mouth?
muleyboy is offline  
Old September 14, 2012, 05:52 PM   #4
noylj
Senior Member
 
Join Date: October 21, 2007
Location: Between CA and NM
Posts: 494
You don't need much lube, but trying to use as little as possible can lead to NOT using enough. I use a light spray coating and don't worry about removing it--Never have in 40 years of reloading and I figure it almost all comes off with all the handling the case/round undergoes.
Lube only needs to be on the body of the case, not the shoulder or neck.
I assume the stuck case came out in one piece and didn't leave any parts in the die? I assume the removal of the stuck case did not damage the die?
You haven't reset the depriming pin so high that the expander plug is interfering with the case sizing section of the die?
There just aren't that many things happening in a sizing die and an inspection of the inside should show any problem.
I have never needed to lube a case neck, but many people seem to. If I was lubing the case neck, I would use graphite or mica--certainly not any oil/grease.
noylj is offline  
Old September 15, 2012, 01:34 PM   #5
mikld
Senior Member
 
Join Date: February 7, 2009
Location: Southern Oregon!
Posts: 1,084
I would think a "buldge" at the base of the neck would indicate the sizing die hasn't sized that portion of the case...
__________________
My Anchor is holding fast!
mikld is offline  
Old September 15, 2012, 02:13 PM   #6
PA-Joe
Senior Member
 
Join Date: June 9, 2010
Location: NEPA
Posts: 729
Too much lube.
PA-Joe is offline  
Old September 15, 2012, 03:53 PM   #7
jcwit
Senior Member
 
Join Date: October 28, 2007
Location: Upper Indiana
Posts: 593
What kind of lube are you using?
__________________
U.S. Army Veteran
NRA Certified Range Officer
jcwit is offline  
Old September 15, 2012, 06:12 PM   #8
muleyboy
Junior Member
 
Join Date: September 14, 2012
Location: Tollhouse California
Posts: 3
Okay so I figured it out! When I took the decapping pin put the expander ball got unscrewed from the pin and was still in the stuck case! Trying to extract it now....thanks for the i put y'all! Definitely things that I need to watch out for in the future!
muleyboy is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 09:11 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.08638 seconds with 7 queries