The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old September 9, 2012, 09:19 AM   #1
rebs
Senior Member
 
Join Date: January 10, 2012
Posts: 2,295
dillon rl 450 ?

Does anyone have one and can tell me about it, pro's and con's ?
rebs is offline  
Old September 9, 2012, 09:23 AM   #2
WESHOOT2
Senior Member
 
Join Date: February 20, 1999
Location: home on the range; Vermont (Caspian country)
Posts: 14,270
Call Dillon direct and ask.
__________________
.
"all my ammo is mostly retired factory ammo"
WESHOOT2 is offline  
Old September 9, 2012, 10:24 AM   #3
243winxb
Senior Member
 
Join Date: July 26, 2011
Posts: 1,066
Dillon RL 450

Have one, bought new years ago. It loads ammo slowly. Had a major problem with shell plates for bottle neck cartridges. The 223 shell plate is a different thickness at each station. The shoulder can be set back way to much on full lenght sizing, causing case separations. Always use a cartridge gage like L E Wilson to chech sizing. The press now needs a rebuild, so Dillon thinks, but it has always had a problem at the sizing station. When FL sizing 45 acp the case cant always find the die mouth, requiring hand positioning of the brass. Slop in the linkage from new, causes this, but an allignment pin can help. This adjusts the subplate. Newer modern dies have more of a flare on the FL carbide dies, helping alignment. Follow photo album link below for Dillon RL 450 pic album & info.
243winxb is offline  
Old September 9, 2012, 03:18 PM   #4
1stmar
Senior Member
 
Join Date: March 21, 2012
Location: Connecticut
Posts: 1,329
You can upgrade a 450 to a 550
1stmar is online now  
Old September 9, 2012, 03:54 PM   #5
243winxb
Senior Member
 
Join Date: July 26, 2011
Posts: 1,066
Dillon RL 450 Test

There is a test to see if the linkage is worn. Move the operating handle so its parallel to the floor. Move handle left and right. If the ram & sub-plate rotate a large amount, it needs a upgrade/rebuild.
243winxb is offline  
Old September 9, 2012, 11:55 PM   #6
medalguy
Senior Member
 
Join Date: August 31, 2009
Location: New Mexico
Posts: 1,020
I have 2 of them I use for rifle cases. I've never had a problem with either of them except for adjustments to the priming system, hence I only use them for rifle cases and I don't use the 450 for priming.

I prepare all the brass on a single stage press, them prime on a bench-mounted RCBS Autoprime. Next the brass goes into the 450, where I charge, seat, and crimp the cases.

The 450 is not the best press for pistol cases. You will want to upgrade to the 550, or probably better yet, sell the 450 on evilbay, and buy a new 550. The 450 will do very well for pistol cases in one pass.

Depending on the type ammo you want to reload, the 450 might work very well, or a 550 might be better.
medalguy is offline  
Old September 10, 2012, 09:34 AM   #7
BDS-THR
Senior Member
 
Join Date: June 12, 2010
Posts: 474
Dillon 450 is a 4 station progressive press without removable tool head for dies and came with manual powder/primer feed attachments and manual shellplate advance.

Because of manual powder/primer feed, progressive loading on 450 can be slow but you can upgrade both with a conversion kits from Dillon.

I have 2 other progressives (1 turret and 2 single stage presses) so the 450 is used dedicated to a caliber and solid top works like a single stage to give me precise OAL consistency control which I like.

http://www.dillonprecision.com/#/content/p/8/catid/6

450 to 550 conversion body with removable tool head will cost you $95, auto powder measure $89, auto priming attachment $86, auto case eject $60, low primer warning kit $26. The upgrade will run you around $350 but you can sell the solid top body to recoup some of the upgrade cost.
BDS-THR is offline  
Old September 11, 2012, 08:49 PM   #8
crowbeaner
Senior Member
 
Join Date: June 4, 2007
Location: Upstate SC
Posts: 1,943
I have an RL450 bought new and still running. I can't begin to count how many rounds in various calibers it's loaded; several thousand this year alone. I consider it the best reloader ever made by anyone at any price. you can have your 550 if you want; I'll stick with my manual operation. No double charges, no empty rounds, nada. When I get enough money saved up, I'm going to buy another used one for dedicated 223 and 380 loading. I've had a 650, SDB, and a 550. I sold them all and still load on the 450. I may not break the world record for amount loaded in an hour, but I'm retired and don't have anything but time. YMMV. CB.
__________________
If you want your children to follow in your footsteps, be careful where you walk.
Beware the man that only owns one gun; he probably knows how to use it.
I just hope my ship comes in before my dock rots.
crowbeaner is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 06:49 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07048 seconds with 7 queries