The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Smithy

Reply
 
Thread Tools
Old August 28, 2012, 04:22 AM   #1
Nine the Ranger
Senior Member
 
Join Date: June 22, 2012
Location: Florida
Posts: 213
Refinishing a stock?

The Work on my 336 will be my first DIY project.

I assume refinishing the stock is as simple as sand, shape, stain.

Am I missing somthing?
__________________
'A Vote is like a Rifle; It's usefulness depends upon the character of the User.'-Theodore Roosevelt

'In a Man to Man fight, the Winner is He who has one more round in his magazine.'-Erwin Rommel
Nine the Ranger is offline  
Old August 28, 2012, 07:06 AM   #2
wyop
Senior Member
 
Join Date: July 15, 2012
Location: Wonderful, Windy Wyoming
Posts: 133
Well, unless your stain is one of those "all in one" products, you'll be missing the oil finish, varnish or lacquer that seals the stock.

What kind of finish do you want when you're done?
wyop is offline  
Old August 28, 2012, 07:23 AM   #3
Doyle
Senior Member
 
Join Date: June 20, 2007
Location: Starkville, MS (new to MS)
Posts: 4,668
Most decent stock don't really need stain. The color of the wood itself is what shines through. For a "working gun", my favorite finish is Minwax Tung Oil Finish. It is a wiping varnish with good durability and repairability. Build it up in about half dozen really light coats at least 24 hours apart. Use steel wool and a tack cloth to wipe off the nubs between coats.
Doyle is online now  
Old August 28, 2012, 07:45 AM   #4
jaguarxk120
Senior Member
 
Join Date: February 28, 2008
Location: Michigan
Posts: 1,928
Your stock may be a smaller piece of wood compared to a end table or dining room set , but it is a fine piece of wood and should be treated as such.

Yes finishing can be boiled down to a few simple steps, BUT those steps are more involved than most people think. Your sanding a piece that has many curves and sharp edges. The inletting areas require special care. The over all condition of the wood will tell you what grades of sanding paper to use.

The final finish can be anything from a spray on poly to many hand rubbed coats of a oil finish.
Start reading about stock finishing and you will find more ways to refinish a stock than there are chances in the lottery.
jaguarxk120 is offline  
Old August 28, 2012, 08:10 AM   #5
tango1niner
Senior Member
 
Join Date: March 5, 2009
Location: rural upstate NY
Posts: 119
To get an idea of how it will look with no stain dampen, not soak the wood with water. Most walnut will look good with no stain. Be sure to let dry throughly. As others mentioned you will need to seal the wood. Seal all bare wood. The object is to keep out moisture. I like tru-oil myself. Apply enough light coats so little or no orange peel texture is visible. 4/0 steel wool between dry coats and a coat of johnsons paste floor wax as a top coat over a lightly steel wooled coat of oil finish. Do not rush the job.
tango1niner is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 08:49 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.06749 seconds with 9 queries