The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting > Bullet Casting

Reply
 
Thread Tools
Old August 18, 2012, 09:36 PM   #1
dagger dog
Member
 
Join Date: September 5, 2010
Posts: 53
LEE 45-70 405gr. FP FB

Any one here using that mold, it's the flat base ? I have read a lot of positive reports on the hollow based version and think that one was designed to obturate well in the old Springfield trapdoor and clones.

I've have my sights set on the H&R CR 871 Buffalo Classic, and want to start shooting it with FFg Goex BP under the 405 gr flat base cast with 75% clip on and 25% stick on mix. My clip WW mix comes in @ 12.5-13 BHN, so I figured the almost pure lead stickys would soften it up some.

Most I have read says you need to compress the load to get it to shoot well, and the 32" barrel requires more lube than the Lee design can hold, may have to go with a lube cookie and over powder wad, to keep fouling to a minimum.

I may have jumped the gun as I have already purchased the mold.

Any and all info on this boolit in any 45-70 rifle, shooting low pressure
< 18,000 smokless or BP would be appreciated.
dagger dog is offline  
Old August 20, 2012, 10:09 AM   #2
PawPaw
Senior Member
 
Join Date: December 24, 2010
Location: Central Louisiana
Posts: 3,112
I use that mold with smokeless, using dead-soft lead and drive it at BP velocities from my H&R Handi rifle. Nothing I've shot with it wanders away. There's no reason it couldn't provide good service with BP loads.

For BP work I use the 459-500-3R, but that's out of my Sharps for longer distances than the Handi. I'd absolutely use a lube cookie between the bullet and powder. I leaned a long time ago that both my rifles like a lube cookie over BP and it's become a standard part of my reloading protocol.
__________________
Dennis Dezendorf

http://pawpawshouse.blogspot.com
PawPaw is offline  
Old August 22, 2012, 07:59 PM   #3
chiefr
Senior Member
 
Join Date: January 27, 2010
Location: AR
Posts: 1,223
I too use this mould and when casting pure lead, the bullets drop out weighing consistently around 430gr. May not be a big deal for modern rifles, but those firing the old trapdoors could see a problem.
Even using 95% lead, the bullets weigh 415gr or more. I have had to reduce loads and work up.
chiefr is offline  
Old August 23, 2012, 10:14 AM   #4
Edward429451
Junior member
 
Join Date: November 12, 2000
Location: Colorado Springs, Colorado
Posts: 9,494
I use that boolit with smokeless powder. I've cast them from 20/1 and from straight WWs. They do fine with ww alloy so what the hey. I shoot them from a guide gun and they're good enough for government work (read hunting).

It's a good boolit with the only drawback being the single cav mould, lol. I have no idea how it would be with BP.
Edward429451 is offline  
Old August 23, 2012, 05:10 PM   #5
dagger dog
Member
 
Join Date: September 5, 2010
Posts: 53
Thanks to all !


Wondering, would you need a chain hoist if Lee made that mold in a SIX cavity ?
dagger dog is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 06:32 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.05944 seconds with 7 queries