Range report...or...beginning of a learning curve. - Page 2

Hawg Haggen · August 17, 2012, 08:42 PM

I'm pretty sure Winchester makes them.

arcticap · August 19, 2012, 04:08 AM

They certainly resemble CCI's in primer material color, size and being labeled as magnum strength and many folks recognize that.
Even ClemBert's independent measurements for the Winchester Magnum #11's matched mykeal's measurements for the CCI #11 standard.

See posts #4 and #19 in this thread:

http://thefiringline.com/forums/showthread.php?t=343254

There's a photo in post #1 of the thread linked below that will really make one chuckle. A whole rack of Winchester #11 Magnum clamshell packs were filled with CCI #11 standard tins at a local Walmart.

http://www.huntingnet.com/forum/blac...-printing.html

Doc Hoy · August 19, 2012, 08:00 AM

..Winchester WLPs. The problems I had (I believe) were my own fault in not seating the primers correctly.

The CCIs were on the same shelf with the Winchesters. Only reason I bought the Winchesters is that I happened to have thumbed through a reloading guide which only referenced Winchester Primers.

The LGS sells Winchesters at 3.00 a hundred and gives ten percent off so I will continue to try them.

It is entirely possible that had I used a different primer, I might have had fewer problems because it is possible that other primers are more forgiving.

Now that I still have the Auto-Primer, I will try ti and keep tack of the rounds I use the Auto-Primer for and which I use the press mounted primer.

I have been away for a week and so I have not even caste the slugs for my next shooting day.

I did get the Lee Hardness Test set. I got the idea now and we shall see how that works too.

Beagle333 · August 19, 2012, 08:52 AM

I have been experimenting with some heavier bullets in my .357, and when I load the 200gr and 218gr bullets, the combination of a large cast bullet and some thick lube makes for a great piston, and I have had a few primers back out slightly from the pressure when I seated the bullet quickly. If I go slowly with my press, I haven't seen that happen. 'Just a thought.

Doc Hoy · August 19, 2012, 01:40 PM

Thanks for the input.

I am in the process of cleaning up the spent shells. When I get them ready I am going to pay very close attention to the seating of the primers and I will keep in mind all of the words of wisdom y'all have given me. So far nothing conflicts. Everything makes sense.

August 17, 2012, 08:42 PM	#26
Hawg Haggen Senior Member Join Date: September 8, 2007 Location: Mississippi Posts: 10,225	I'm pretty sure Winchester makes them. __________________ http://blackpowdertimes.com/index.php

August 19, 2012, 04:08 AM	#27
arcticap Senior Member Join Date: March 16, 2005 Location: Central Connecticut Posts: 2,961	They certainly resemble CCI's in primer material color, size and being labeled as magnum strength and many folks recognize that. Even ClemBert's independent measurements for the Winchester Magnum #11's matched mykeal's measurements for the CCI #11 standard. See posts #4 and #19 in this thread: http://thefiringline.com/forums/showthread.php?t=343254 There's a photo in post #1 of the thread linked below that will really make one chuckle. A whole rack of Winchester #11 Magnum clamshell packs were filled with CCI #11 standard tins at a local Walmart. http://www.huntingnet.com/forum/blac...-printing.html Last edited by arcticap; August 20, 2012 at 03:10 AM.

August 19, 2012, 08:00 AM	#28
Doc Hoy Senior Member Join Date: October 24, 2008 Location: Chesapeake, VA Posts: 3,340	I used... ..Winchester WLPs. The problems I had (I believe) were my own fault in not seating the primers correctly. The CCIs were on the same shelf with the Winchesters. Only reason I bought the Winchesters is that I happened to have thumbed through a reloading guide which only referenced Winchester Primers. The LGS sells Winchesters at 3.00 a hundred and gives ten percent off so I will continue to try them. It is entirely possible that had I used a different primer, I might have had fewer problems because it is possible that other primers are more forgiving. Now that I still have the Auto-Primer, I will try ti and keep tack of the rounds I use the Auto-Primer for and which I use the press mounted primer. I have been away for a week and so I have not even caste the slugs for my next shooting day. I did get the Lee Hardness Test set. I got the idea now and we shall see how that works too. __________________ Doc My reading of history convinces me that most bad government results from too much government. Thomas Jefferson

August 19, 2012, 08:52 AM	#29
Beagle333 Senior Member Join Date: January 7, 2012 Location: Back in the woods a piece Posts: 740	It might be this..... I have been experimenting with some heavier bullets in my .357, and when I load the 200gr and 218gr bullets, the combination of a large cast bullet and some thick lube makes for a great piston, and I have had a few primers back out slightly from the pressure when I seated the bullet quickly. If I go slowly with my press, I haven't seen that happen. 'Just a thought.

August 19, 2012, 01:40 PM	#30
Doc Hoy Senior Member Join Date: October 24, 2008 Location: Chesapeake, VA Posts: 3,340	Beag, Thanks for the input. I am in the process of cleaning up the spent shells. When I get them ready I am going to pay very close attention to the seating of the primers and I will keep in mind all of the words of wisdom y'all have given me. So far nothing conflicts. Everything makes sense. __________________ Doc My reading of history convinces me that most bad government results from too much government. Thomas Jefferson