The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Smithy

Reply
 
Thread Tools
Old August 4, 2012, 11:06 PM   #1
westfi1
Member
 
Join Date: April 22, 2005
Posts: 32
Help

I have a S&W model 29 that is busted. I would like to try to fix it myself, but I have never been inside a S&W revolver. Is there a non-video tutorial available to teach me disassembly ? Thanks very much in advance.
westfi1 is offline  
Old August 4, 2012, 11:47 PM   #2
wyop
Senior Member
 
Join Date: July 15, 2012
Location: Wonderful, Windy Wyoming
Posts: 133
You could buy the Kuhnhausen's manual on S&W revolvers:

http://www.midwayusa.com/product/314...rry-kuhnhausen
wyop is offline  
Old August 5, 2012, 01:00 PM   #3
drail
Junior member
 
Join Date: February 2, 2008
Posts: 3,150
If you have any intention of "fixing" a S&W revolver buy the Kuhnhausen Shop Manual. It will save you a lot of money and frustration and mistakes in the long run. It is well worth the price. There is a lot more going on inside a S&W than you think and parts will not just "drop in". Just watching a video won't tell you enough either (especially since the majority of the videos I have seen are completely wrong.)
drail is offline  
Old August 5, 2012, 01:36 PM   #4
PetahW
Senior Member
 
Join Date: September 19, 2008
Posts: 4,565
Sometimes, S&W will surprise - I've bought used S&W's, only to send them in to S&W's Service Dept for repairs (legal under Federal Law for anyone to do), and got them back as new, for the bubble.


.
PetahW is offline  
Old August 5, 2012, 07:18 PM   #5
James K
Staff
 
Join Date: March 17, 1999
Posts: 18,644
A better definition of "busted" might help. It could mean anything from some dirt in the action to a gun blown to pieces.

Jim
__________________
Jim K
James K is offline  
Old August 5, 2012, 07:52 PM   #6
westfi1
Member
 
Join Date: April 22, 2005
Posts: 32
Help

You are right, Jim - I was way too vague. What is happening is I can cock the gun with the hammer in single action mode, and everything is fine; the cylinder rotates and locks up, the hammer stays back, the trigger moves back, etc. But when I pull the trigger to fire the gun, the hammer doesn't fall, it just stays back in the fully cocked position. The trigger moves back far enough to release the sear but the hammer just doesn't move. If you keep the trigger held back and push the hammer forward, it will fall, but takes quite a bit of pressure to do so.
The same thing also happens occasionally in double action mode but not as often. Maybe this will give some insight into the problem. Thanks so much once again.
westfi1 is offline  
Old August 5, 2012, 08:35 PM   #7
Dfariswheel
Senior Member
 
Join Date: May 4, 2001
Posts: 6,773
The Kuhnhausen manual has everything you need to disassemble, diagnose, repair, and reassemble your S&W.
The manual shows all work the way they do it at the factory.

I recommend ordering it from Brownell's so you can also order a Brownell's Magna-Tip gunsmith screwdriver set made specifically for the S&W.
These drivers will prevent damaging the screws:

http://www.brownells.com/.aspx/pid=2...-A-SHOP-MANUAL

http://www.brownells.com/.aspx/pid=4...-W-SCREWDRIVER
Dfariswheel is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 09:39 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2013 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07276 seconds with 9 queries