The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old July 8, 2012, 10:19 PM   #1
mohr308
Senior Member
 
Join Date: January 15, 2012
Location: Western New York
Posts: 428
Switching Brass

I have picked up 500 cases of once fired LC 5.56 brass. I have been loading PMC brass for a while now. Since I'm switching, will I expect to re-work all my loads? I have a feeling I am but might as well get a little input.
mohr308 is offline  
Old July 8, 2012, 10:30 PM   #2
mrawesome22
Senior Member
 
Join Date: November 9, 2005
Location: Ohio, Appalachia's foothills.
Posts: 3,779
When changing any component or lot number, reduce.

A chronograph and records of your established loads will get you back on track very quickly.

Sent from HenseMod6.
mrawesome22 is offline  
Old July 8, 2012, 10:34 PM   #3
Jim Watson
Senior Member
 
Join Date: October 25, 2001
Location: Alabama
Posts: 11,412
Weigh the brass. If the LC is heavier, it will call for a load reduction. If not, I would not sweat it unless I were already loading at the maximum.


It may call for primer crimp swaging or reaming, too.
Jim Watson is online now  
Old July 8, 2012, 10:35 PM   #4
Marco Califo
Senior Member
 
Join Date: April 4, 2011
Location: LA
Posts: 879
Click on this for a table of 223 case weights and water capacity.http://thefiringline.com/forums/atta...4&d=1336880187
They are so close, around 1% differences, that IMO you do not have much to worry about. At less than max loads, for 223, a change in brass, even between Mil and commercial, is insignificant.

7.62/308 DO Vary much more. In 308, yes you would work up again.
__________________
........................................................
Marco Califo is offline  
Old July 9, 2012, 12:00 AM   #5
mohr308
Senior Member
 
Join Date: January 15, 2012
Location: Western New York
Posts: 428
all the brass came swaged. I will start just below and work up quick to my norm.
mohr308 is offline  
Old July 9, 2012, 09:15 AM   #6
Edward429451
Junior member
 
Join Date: November 12, 2000
Location: Colorado Springs, Colorado
Posts: 9,494
By all means, do weigh them. IIRC, PMC is on the heavy side for 223 brass, so you will probably be fine.
Edward429451 is offline  
Old July 9, 2012, 08:16 PM   #7
tobnpr
Senior Member
 
Join Date: August 1, 2010
Location: Tampa Bay
Posts: 3,232
delete
tobnpr is offline  
Old July 9, 2012, 10:12 PM   #8
hk33ka1
Senior Member
 
Join Date: April 20, 2010
Posts: 275
It depends where you are on your charges. If the book says for example 63gr Varget, 66.5 max and youre already at 66.3gr I'd back off. But if you are at the lower end of things ex. 63-64gr I would start off there whether changing brass or trying a combination for the first time.
hk33ka1 is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 08:59 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07537 seconds with 7 queries