The Firing Line Forums

Go Back   The Firing Line Forums > The Hide > The Art of the Rifle: Bolt, Lever, and Pump Action

Reply
 
Thread Tools
Old July 4, 2012, 10:04 AM   #1
Pond, James Pond
Senior Member
 
Join Date: July 12, 2011
Location: Top of the Baltic stack
Posts: 2,426
Zeroing your scope. What distance?

I realise that this will, in part, be personal preference, but 100yds seems to be the general standard on most rifles.

But what about .22s??

I should have my scope delivered by this time next week and I was wondering which distance to choose.

Given the range of a 22L, my guess was that I should err towards 75 m or even 50 m.

Is this sound logic or is there another, recognised ideal zero distance for .22s?
__________________
You cannot wake someone who is pretending to sleep. Stop pretending. Wake up.
Doubt: ...it's the only thing I'm sure of...
-Marsupials: Nature's idea of Concealed-Carry-
Pond, James Pond is online now  
Old July 4, 2012, 10:29 AM   #2
Skimp
Member
 
Join Date: June 12, 2012
Posts: 62
When zeroing the .22 set zeroing targets at 10, 20, 30, 40, 50, and 100 yards, then find the mark at each range. If you are using a scope, and the scope center is 2-inches above bore center, at 10 yards the bullet will hit 2-inches below the bullseye.

Depending on the type of scope, I strive to be bullseye level at 50 yards.

I use this calculator to get the trajectory path before going to the range: http://www.handloads.com/calc/
Skimp is offline  
Old July 4, 2012, 01:34 PM   #3
huntinaz
Senior Member
 
Join Date: September 21, 2010
Location: az
Posts: 951
I use my 22's mostly for squirrel hunting and the average shot is probably ~ 20 yards... so that's where I zero. I'd say zero for your application.
__________________
Wanted: 50 Beowulf Brass, .500 cal bullets

"Once you quit hearing sir and ma'am, the rest is soon to follow." - Cormack McCarthy
"I'm just an average Joe, although I did score 4 touchdowns in one game..."-Al Bundy
huntinaz is offline  
Old July 4, 2012, 02:10 PM   #4
tobnpr
Senior Member
 
Join Date: August 1, 2010
Location: Tampa Bay
Posts: 2,765
Can't speak to .22's, but other shooters usually zero at 100-300 yards, depending on the distances most commonly shot. 100 yards is common, because that's the maximum distance available to many shooters on public ranges.

Long-range shooters usually zero at 200 or 300, as this requires less adjustment for the longer shots.

Hunters often zero to maximum point blank range (as explained in a prior thread of yours) for the ammunition being used.
tobnpr is offline  
Old July 4, 2012, 03:19 PM   #5
SteelChickenShooter
Senior Member
 
Join Date: May 12, 2011
Posts: 838
For a very common setup, zeroing at 75 yards works well.
Small game hunters may want to zero at 50 so you are never more than a bit high or a bit low using CCI minimags for squirrel.
I use a Burris ballistic reticle scope so my cross hairs are zero at 40 meters. The first mark lines up at 60 meters, the second at 77 meters, and the third hash mark lines up at 100 meters. Therefore I aim center of body at the four distances using the ballistic scope. I used to adjust a Leupold target knob scope, but have replaced that scope using this Burris Fullfield scope which needs no adjustment during a shooting match.
SteelChickenShooter is offline  
Old July 4, 2012, 03:21 PM   #6
Mobuck
Senior Member
 
Join Date: February 2, 2010
Posts: 1,969
I zero 22 rifles at 25 yards unless I have a specific need to shoot them at longer range. I normally step up to a 17HMR if I expect shots at 100+ yards. I've shot enough 22's to know pretty close to where they hit at 100 yards with a 25 yard zero.
Mobuck is offline  
Old July 4, 2012, 04:09 PM   #7
JerryM
Senior Member
 
Join Date: April 4, 1999
Location: New Mexico
Posts: 1,884
For a big game rifle in mostly open country the old rule of three works. It is 3" high at 100 yards.
Jerry
__________________
Ecclesiastes 12:13 *¶Let us hear the conclusion of the whole matter: Fear God, and keep his commandments: for this is the whole duty of man.
14 *For God shall bring every work into judgment, with every secret thing, whether it be good, or whether it be evil.
JerryM is offline  
Old July 4, 2012, 04:27 PM   #8
wogpotter
Senior Member
 
Join Date: September 27, 2004
Posts: 2,724
Simple caliber independant answer for evey gun ever made.
Zero at the distance you will use it at the most.

THEN figure out the changes for other distances.
__________________
Allan Quatermain: “Automatic rifles. Who in God's name has automatic rifles”?

Elderly Hunter: “That's dashed unsporting. Probably Belgium.”
wogpotter is offline  
Old July 4, 2012, 04:59 PM   #9
jmr40
Senior Member
 
Join Date: June 15, 2008
Location: Georgia
Posts: 5,493
A 22 with optics is zeroed at 50, iron sights at 25. I then shoot at ranges closer and farther and make a note of how much high or low they may be.
jmr40 is offline  
Old July 4, 2012, 05:18 PM   #10
Doyle
Senior Member
 
Join Date: June 20, 2007
Location: Starkville, MS (new to MS)
Posts: 4,542
Learn to use the "Maximum point blank range" technique. I'm not going to go into details of it here since it is readily available on Google but essentially it determines the ideal zero distance for any given caliber (i.e., the flatter shooting the caliber, the greater the MPBR zero distance).
Doyle is offline  
Old July 4, 2012, 05:22 PM   #11
FrosSsT
Senior Member
 
Join Date: July 17, 2011
Location: NJ
Posts: 570
The caliber does not matter. Wether it is.a 22lr or a 50cal you need to zero in at the distance you plan on shooting at. Period.
FrosSsT is offline  
Old July 4, 2012, 08:01 PM   #12
Kreyzhorse
Senior Member
 
Join Date: April 12, 2006
Location: NKY
Posts: 11,376
I shoot at 100 yards and that is what I zero my scope at. As others mentioned, you zero to your application and anticipated average shooting distance.
__________________
"He who laughs last, laughs dead." Homer Simpson
Kreyzhorse is offline  
Old July 4, 2012, 08:26 PM   #13
mete
Senior Member
 
Join Date: June 14, 2004
Location: NY State
Posts: 5,151
Parallax on 22 scopes is 75 yds IIRC.
__________________
And Watson , bring your revolver !
mete is offline  
Old July 4, 2012, 08:43 PM   #14
4runnerman
Senior Member
 
Join Date: January 16, 2010
Location: Minnsota
Posts: 2,656
Mine are both set to 50 yards.
__________________
NRA Certified RSO
NwCP- Performance Isn't Optional
4runnerman is online now  
Old July 4, 2012, 09:54 PM   #15
kmaysob
Senior Member
 
Join Date: December 9, 2011
Posts: 186
i keep my .22 and .17 zeroed at 50 yards and work up from there. i dont use "22" scopes. my .22 has a pentax 3-9-40 on it and the .17 has a vortex 4-12-40 on it.

the distance i shoot with the .22 is dependent on the ammo. shooting cheap bulk pack, its pointless to try for much more than 50 yards. with the higher end "target" ammo, i can push 100+
kmaysob is offline  
Old July 4, 2012, 11:42 PM   #16
trg42wraglefragle
Senior Member
 
Join Date: April 21, 2008
Location: new zealand
Posts: 791
Mines set at 50yards.
I don't really shoot any animals past 70yards so it suits me fine.
Really depend what you intend on shooting with your 22.
trg42wraglefragle is offline  
Old July 5, 2012, 06:22 AM   #17
phil mcwilliam
Senior Member
 
Join Date: July 18, 2007
Posts: 573
Mines zeroed for 75 yards. This makes it good at 25 yards, 1 inch high at 50 yards, and about 3 to 4 inches low at 100 yards, give or take depending on ammunition. I use my CZ .22 mainly for hunting.
phil mcwilliam is offline  
Old July 5, 2012, 06:59 AM   #18
gun nut
Senior Member
 
Join Date: June 7, 2009
Location: midwest
Posts: 298
For my 22 it would be either 50 or 75 yards depending on my sights/optics and what I intended to shoot with it. Sounds like your right on James!
__________________
The only stupid question is the one not asked! (Unknown)
gun nut is offline  
Old July 5, 2012, 09:38 AM   #19
Art Eatman
Staff Lead
 
Join Date: November 13, 1998
Location: Terlingua, TX, USA
Posts: 22,041
For general usage purposes, I'm in phil mcwilliams' camp. Otherwise, zeroing for closer distances depends on the specific purpose.
__________________
You're from BATFE? Come right in! I use all your fine products!
Art Eatman is offline  
Old July 5, 2012, 10:13 AM   #20
jimbob86
Senior Member
 
Join Date: October 4, 2007
Location: All the way to NEBRASKA
Posts: 6,452
Depends upon the rifle.

My deer rifle I keep zeroed at 300: +4" high at 100 (chest underlined by horizontal crosshair), just over 4" at 200 (same), 0" at 300 (duh), 11" low at 400(top of the back) ....... a holdover of a foot will get a center hit at 450....

I have a 7-08 with a 16" barrel I download a 150 gr bullet to 2400 f/sec for, for the kids to use..... it's zeroed for 100 and is 6" low at 200. The kids have not shown an ability to consistantly hit milk jugs beyond that distance .... so they can't shoot at deer past that.

The .22's are all zeroed at 50.
__________________
TheGolden Rule of Tool Use: "If you don't know what you are doing, DON'T."

http://nefirearm.com/
jimbob86 is offline  
Old July 6, 2012, 11:19 PM   #21
RC20
Senior Member
 
Join Date: April 10, 2008
Location: Alaska
Posts: 1,870
James, Mixing 22 and a large game rifle is a non comparable.

Big game shooting is not target shooting, you want to be able to just aim and shoot at anything out to 200-300 yds. That takes care of most shots if they are a snap shoot, aim at the middle and you are going to hit it in the vitals.

So, 2 inches high at 100 gets you on at 200 and you drop off at 300. Hold a bit high at 300 or top of the back at 350-400 and it will hit the vitals.

Above poster does it a bit higher and goes out a bit further for a dead on shot, same idea but extends his range and he has the cross hairs figured to make the long shots.

22? 50 is common, but if you are hunting rabbits at less, then 20 or 30 makes sense. 22 looses a lot quickly and drops fast. Keep it inside the 50 and you are good. You can sight at 100 but then way off at shorter. Starting to mortar them at 100. Its an inside 50 yd or meter round.
RC20 is offline  
Old July 7, 2012, 01:10 AM   #22
bamaranger
Senior Member
 
Join Date: October 9, 2009
Location: North Alabama
Posts: 4,088
depends

My general purpose, everyday .22's, both scoped, are "on" at 50 yds, with Rem bulk pack HP's.

But, I have a 9" pieplate sized gong set up on the corner of my place that is about 125 yds off. A CMP Mossberg 44 with peep sights is set up to shoot "on" with a 6 o'clock hold for it, and affords me peep sight practice that is pretty satisfyig. It shoots Rem bulk pac too.

Finally my Savage TR .22 is zeroed on at 100. The scope for it has tac knobs and I can click away for range and wind and get some come up and wind practice. The TR gets CCI hi vel.
bamaranger is offline  
Old July 7, 2012, 03:55 AM   #23
MarkDozier
Senior Member
 
Join Date: February 1, 2010
Posts: 329
1 is set for 100 yards. exactly 2 inches high at 25 yards. The other is I don't, butit is dead on at both 25 and 50.
MarkDozier is offline  
Old July 8, 2012, 01:43 AM   #24
Marquezj16
Senior Member
 
Join Date: April 3, 2011
Posts: 2,088
I zero mine at 50 yards and then use Nikon's Spot On to figure out my adjustments for the other ranges.

http://www.nikonhunting.com/spoton/
Marquezj16 is offline  
Old July 8, 2012, 11:38 AM   #25
sc928porsche
Senior Member
 
Join Date: May 29, 2008
Location: now living in alabama
Posts: 2,433
For the 22lr, I zero at 75yds. For the lever actions (30-30 and 45/70) I use 100yds. For the flat shooters (25-06, 7mm mag, 300WM etc.) I use 200yds. The rest (22-250, 260 rem, 308, 30-06, etc.) are zero at 100yds.

For the most part, it depends on the game the terrain and the cartridge that you hunt with.
__________________
No such thing as a stupid question. What is stupid is not asking it.
sc928porsche is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 01:19 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2013 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.14695 seconds with 7 queries