The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old July 4, 2012, 08:10 AM   #1
DesMarx
Junior Member
 
Join Date: July 4, 2012
Posts: 2
Need Help .243 Sako Forester

Hi There
Please can somebody assist me.
I am reloading a Sako .243 Forester.

Problem: After firing my rounds, I have GREAT difficulty in lifting the bolt in order to remove the spent cartridge. This Only happens with my reloads, and not purchased/first time fired rounds.

Please note that the following can be removed from possible causes:

Hot rounds (overloading with powder)

I am at the point of giving up......

Can anybody be of assistance ?
DesMarx is offline  
Old July 4, 2012, 10:45 AM   #2
Slamfire
Senior Member
 
Join Date: May 27, 2007
Posts: 4,016
You need to give us an idea of your loads, and it would help if you had pictures of your loaded and fired reloads.

I will say, regardless of your loading data, if your SAKO functions perfectly with factory ammunition, but not your reloads, I can say with a 99.999% expectation of being correct, your reloads are too hot.

Now what is causing that, not enough information to really provide a good analysis.

Some things to consider. Always trim your cases. Cases grow the most on the first firing, if you did not trim, it is highly likely the case neck is pinced in the throat.

How do you measure your powder charges? Scoops or do you weigh?
__________________
If I'm not shooting, I'm reloading.
Slamfire is offline  
Old July 4, 2012, 11:03 AM   #3
PawPaw
Senior Member
 
Join Date: December 24, 2010
Location: Central Louisiana
Posts: 3,108
Lots of reasons why that might happen, and Slamfire covered most of them. One problem I had a couple of years ago was my rifle would have a hard opening after firing and we finally narrowed it down to a too-long machine screw that was binding the bolt. Why it would only bind after firing was a bit of a mystery, but we ground off one thread and the problem went away.
__________________
Dennis Dezendorf

http://pawpawshouse.blogspot.com
PawPaw is offline  
Old July 6, 2012, 12:24 PM   #4
crowbeaner
Senior Member
 
Join Date: June 4, 2007
Location: Upstate SC
Posts: 1,938
My feeble faculties wander toward case lube left on the case letting the fired case back out of the chamber and pushing against the bolt face, and the fact that you may have to lightly lap the chamber to remove a burr or excess metal left from the reaming process. Do your fired cases have any kind of shiny spot on them caused by a piece of metal? Have you cleaned the chamber with an ammonia solvent? Many rifles in 243 have a tight chamber; I'd try sizing your reloads with a small base die and see if that changes things. Too long case length will cause pressures to rise as noted above.
__________________
If you want your children to follow in your footsteps, be careful where you walk.
Beware the man that only owns one gun; he probably knows how to use it.
I just hope my ship comes in before my dock rots.
crowbeaner is offline  
Old July 6, 2012, 04:38 PM   #5
Kiwi Hunter
Member
 
Join Date: August 13, 2009
Posts: 76
Can you give some details on how you know your reloads arent hot? You may have overlooked something? Dumped powder from a measure back into the wrong container? Old powder? Scale needs calibrating (weigh a projectile).

A projectile jammed tight into the lands can raise pressure - an old Sako could have a very short throat compared to a modern Rem etc. That combined with a tight chamber + thick brass could make a "max book load" well over max for that rifle.

If your loaded rounds chamber and eject normally before firing then I would try firing a round with an absolute minimum charge from a new supply with the projectile seated well back from the lands and see if the problem goes away - work forwards from that point.

Always interesting to see how a problem resolves - please post any solution you find?
Kiwi Hunter is offline  
Old July 6, 2012, 05:02 PM   #6
hooligan1
Senior Member
 
Join Date: July 18, 2010
Location: Independence Missouri
Posts: 3,249
You need to "full length" resize, adjust your die down when the ram is at it's highest point until it lightly kisses the shell holder, then chamber the brass and make sure it fits nicely.

Also some powder bullet combinations are the reason for "hard bolt lift", try to reduce some powder weights (if you must use the same powder) by 10%.
__________________
Thanks for coming!
hooligan1 is offline  
Old July 6, 2012, 05:35 PM   #7
judgecrater
Member
 
Join Date: March 6, 2012
Posts: 52
Sounds like too hot of a load. Any other symptoms of overpressure? Flattened primers? Cratering?
judgecrater is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 06:51 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07428 seconds with 7 queries