The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Smithy

Reply
 
Thread Tools
Old November 10, 2012, 11:42 AM   #1
brmfan
Senior Member
 
Join Date: October 21, 2008
Posts: 530
Stuck bullet removal question

Okay... it finally happened. Was testing subsonics (180 flat base sp, new Lapua brass, 10.0 Trialboss, CCI 200 primers) for stability. First 3 were fine- stable at 75 yards and very accurate- no problems. also, barrel was clean but not oiled.

Put the suppressor on for the 4th shot and POOT... nothing! Checked and the bullet is stuck about 4" in front of the chamber. Rifle is a Remington 5R cut down to 21.75"

I plan on soaking it in Kroil overnight and using a wooden dowel to tap it out but since it is a soft point is it better to tap it towards the chamber (shortest distance) or out the muzzle???
brmfan is offline  
Old November 10, 2012, 03:03 PM   #2
brmfan
Senior Member
 
Join Date: October 21, 2008
Posts: 530
Got it!

Soaked the bore from the chamber end in Du Pont teflon penetrant for 15 minutes. Took a 1/4" steel dowel, wrapped duct tape at one end and 6" below that until the wrapped sections mic'd .290"

Inserted from muzzle, and after about a dozen hard whacks the bullet came out. After cleaning a visual inspection from both ends looks good. Best I can manage without a bore scope.
brmfan is offline  
Old November 10, 2012, 03:06 PM   #3
natman
Senior Member
 
Join Date: June 24, 2008
Posts: 1,369
Good approach, but if it happens again use a BRASS rod, not steel. Brass won't risk scratching the bore.
natman is offline  
Old November 10, 2012, 03:15 PM   #4
brmfan
Senior Member
 
Join Date: October 21, 2008
Posts: 530
Natman: I agree 100% but I live in a rural area and that's all Lowes had. I did chamfer the edge of the dowel on my bench sander however. Hopefully it's all good!
brmfan is offline  
Old November 11, 2012, 02:25 PM   #5
4V50 Gary
Staff
 
Join Date: November 2, 1998
Location: Colorado
Posts: 16,594
Use a brass muzzle guard if you must do it again with a steel rod.

Glad it's out.
__________________
Vigilantibus et non dormientibus jura subveniunt. Molon Labe!
4V50 Gary is offline  
Old November 11, 2012, 03:19 PM   #6
Jim Watson
Senior Member
 
Join Date: October 25, 2001
Location: Alabama
Posts: 10,892
Have you figured out the cause for the stuck bullet?

Short load?
Trail Boss not as wonderful for rifle loads as claimed?
Some weird interaction with the suppressor?
Jim Watson is offline  
Old November 12, 2012, 02:01 AM   #7
Exibar
Member
 
Join Date: November 4, 2012
Posts: 26
aluminum cleaning rods work well for that too....

scary when it happens, especially if you're at the range!

Mike B
Exibar is offline  
Old November 14, 2012, 12:31 PM   #8
guncrank
Senior Member
 
Join Date: July 15, 2006
Location: Fern Creek ,KY and Metro Louisville at large
Posts: 317
aluminum cleaning rods work well for that too....

scary when it happens, especially if you're at the range!

I would rather use a solid rod brass prefered , steel second to remove a stuck bullet.

Last customer , I had to remove bullet and the alunimum rod used first time.
__________________
CW Shooters Supply Inc
1-866-217-5990
Machine Shop and Finishing Services to the trade and public

Last edited by guncrank; November 14, 2012 at 01:27 PM. Reason: Spelling
guncrank is offline  
Old November 14, 2012, 02:33 PM   #9
Brian Pfleuger
Staff
 
Join Date: June 25, 2008
Location: Central, Southern NY, USA
Posts: 18,336
I assume we're talking .308Win here?

If so, that load is likely too low. QuickLoad thinks it only about 68% fill on default capacity, which is usually low, so the actual % would be lower yet.

QuickLoad thinks that load generates 19kpsi and a muzzle velocity of just 841fps. The bullet is actually slowing down past about 9" in the barrel.

13.0gr should get you around 1,100fps, 12.0 would be around 1,000.
__________________
Still happily answering to the call-sign Peetza.
---
The problem, as you so eloquently put it, is choice.
-The Architect
-----
He is no fool who gives what he can not keep to gain what he can not lose.
-Jim Eliott, paraphrasing Philip Henry.
Brian Pfleuger is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 03:02 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.08423 seconds with 9 queries