The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Smithy

Reply
 
Thread Tools
Old June 16, 2012, 03:25 AM   #1
Regolith
Senior Member
 
Join Date: September 30, 2008
Location: Pacific Northwest
Posts: 400
Firing pin "cratering" on a Stevens 66-B

I think I've posted about this before on this forum when I was looking for a tool that would keep the brass from sticking in the chamber because of this issue (I eventually got a chamber iron that has worked well).

However, now I'm wondering if it would be possible for a gunsmith to fix it permanently.

Here's a picture of what I'm talking about:



I'm wondering if a gunsmith could machine the breech back to get rid of the "crater", and then maybe re-cut the extractor grooves if necessary. You can see two to three threads for the barrel sticking out of the receiver, so I think there MAY be enough room to get the headspacing right. The firing pin would also need to be shaved down so that it didn't impact the metal during a dry fire.

So, would this be something a gunsmith could do relatively easily, or would it be too much to be worth it?
Regolith is offline  
Old June 16, 2012, 05:10 AM   #2
oneoldsap
Senior Member
 
Join Date: September 16, 2009
Location: I live in the foot of the Green Mountains of Vermont
Posts: 1,581
A round file is all that's needed . Just remove the lip on the inside , that was created by dry firing ! I've fixed a bunch of .22s in this manner , mostly Ithica 49s . Is your firing pin peened over too ?
oneoldsap is offline  
Old June 16, 2012, 06:05 AM   #3
Regolith
Senior Member
 
Join Date: September 30, 2008
Location: Pacific Northwest
Posts: 400
The pin looks fine. I'm guessing its made of much harder steel than the breech, or it's been replaced fairly recently.

But I was talking about removing the cosmetic damage and preventing it from happening again. The ironing tool works well enough to keep it functional.
Regolith is offline  
Old June 16, 2012, 06:16 AM   #4
Bailey Boat
Junior member
 
Join Date: December 10, 2006
Location: NC
Posts: 365
Since you already have the chamber ironing tool, round the chamber back out and STOP dry firing it!!!
Very few rimfires can be dry fired without eventually causing damage. If you MUST dry fire this gun, insert a fired case into the chamber before hand.
Bailey Boat is offline  
Old June 16, 2012, 06:22 AM   #5
Regolith
Senior Member
 
Join Date: September 30, 2008
Location: Pacific Northwest
Posts: 400
I don't dry fire it on purpose. It's usually when I'm firing fast and I find out the mag's empty when the gun goes *click*.
Regolith is offline  
Old June 16, 2012, 03:51 PM   #6
g.willikers
Senior Member
 
Join Date: September 28, 2008
Posts: 4,296
It's a pity that all rimfire semiautos don't have a cross pin to prevent the firing pin from hitting the barrel in a dry fire, like Rugers.
Even if the back of the barrel is machined like you suggest, it's bound to happen again.
Just keep your handy tool handy.
On one of mine, that suffered from this problem, I filed a notch just deep enough so the firing pin can't peen the back of the barrel enough, any more, to interfere with a round chambering.
And narrow enough so the rim of the case is still well supported, so the firing pin sets it off.
So far, so good with it.
__________________
Lock the doors, they're coming in the windows.
g.willikers is online now  
Old June 17, 2012, 05:05 PM   #7
Fleet
Senior Member
 
Join Date: December 1, 2011
Posts: 108
The real fix is for you to get a gun that will support what you're wanting to do with it, because if you keep on doing what you're doing, all you'll have is scrap.
Fleet is offline  
Old June 17, 2012, 05:49 PM   #8
oneoldsap
Senior Member
 
Join Date: September 16, 2009
Location: I live in the foot of the Green Mountains of Vermont
Posts: 1,581
That's the only time I've ever heard the word cosmetics used in reference to a Stevens firearm !
oneoldsap is offline  
Old June 17, 2012, 09:24 PM   #9
James K
Staff
 
Join Date: March 17, 1999
Posts: 18,630
Those guns do have a firing pin stop but with wear and battering the pin can protrude too far. The bolt has a countersunk area that encloses the case rim; the non-countersunk part of the bolt face butts up against the barrel face and the firing pin should not protrude past the end of that countersunk area; it should stop in the countersunk area so it never touches the barrel.

A quick and dirty fix is just to grind a bit off the front of the pin so it doesn't protrude beyond the countersunk area. That is a pretty old gun and probably just about everything is worn; might I suggest retiring it and getting a more modern plinker, like the Ruger 10/22.

(I am not sure how well I explained that, but I don't do drawings well. If still unclear, I will try again.)

Jim
__________________
Jim K
James K is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 09:21 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2013 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.08404 seconds with 9 queries