The Firing Line Forums

Go Back   The Firing Line Forums > The Hide > The Art of the Rifle: Bolt, Lever, and Pump Action

Reply
 
Thread Tools
Old June 6, 2012, 12:49 PM   #1
HDmac
Member
 
Join Date: May 23, 2012
Posts: 25
Rings & Bases

Hey guys,
So I ordered up myself a Savage 12 LRP and I also chose a VORTEX Viper 6.5-20x50 PA to go with it. Now I am looking for some hardware in between! I think I want to go with a picatinny style 1 peace rail and to my understanding a 20 moa cant (as in the angle) shouldn't be a problem to zero at 100 yards. With that being said, I am looking for a nice solid rail but I am on a budget.

Any real difference between these two? Aluminum vs. Steel?
http://www.midwayusa.com/product/257...und-rear-matte
http://www.midwayusa.com/product/315...t-action-matte

Also the 12 LRP is a target action, will these fit? Someone had said the recoil lug does not line up.

Secondly, going to need rings with that, the scope has a 30mm tube and a 50mm objective lens, I have no idea what height rings to get, obviously I will want it to be as low as possible, is there any good way figure that out short of ordering them and seeing if they fit?

Last edited by HDmac; June 6, 2012 at 03:45 PM.
HDmac is offline  
Old June 6, 2012, 07:22 PM   #2
DnPRK
Senior Member
 
Join Date: August 24, 2001
Location: LC, Ca
Posts: 1,761
Of the two scope mounts you chose, one has a 20 MOA cant for long range shooting. The other is 0 MOA (no cant), which means you have to rely on the vertical adjustment in the scope for long range shots.

Either mount should serve you well. But given the choice, I would go with the 20 MOA mount.

A third option is EGW. I have them on 3 of my 5 Savages.
EGW 20 MOA for Savage 12 round receiver

An easy way to measure for scope rings is to install the scope mount and place a couple stacks of pennies for the scope to rest upon. You can add or subtract pennies until you get the scope-to-barrel clearance you desire. Then measure the height of the stack of pennies. Most ring manufacturers will list the ring height (distance from the top of the mount rail to the bottom of the scope tube).

I like Leupold QRW rings because they are easy to lap and allow the scope to be easily removed and installed without loss of zero.
DnPRK is offline  
Old June 6, 2012, 07:43 PM   #3
HDmac
Member
 
Join Date: May 23, 2012
Posts: 25
After a quick google, EGW looks like a good brand, I see there are a few aluminum vs. steel rail debates. I might go in the middle and get this one:
http://www.midwayusa.com/product/373...ion-round-rear

Although the lower priced weaver is looking appealing...
http://www.amazon.com/Weaver-Extende...9030759&sr=1-1

Last edited by HDmac; June 6, 2012 at 08:07 PM.
HDmac is offline  
Old June 7, 2012, 02:19 PM   #4
tobnpr
Senior Member
 
Join Date: August 1, 2010
Location: Tampa Bay
Posts: 2,964
I bought the EGW...much better price at SWFA than Midway...

http://swfa.com/EGW-Picatinny-Rail-1...nt-P46208.aspx
tobnpr is offline  
Old June 7, 2012, 02:26 PM   #5
HDmac
Member
 
Join Date: May 23, 2012
Posts: 25
Yeah, I ended up ordering the 20 moa weaver. I think it will do a good job, and if it doesn't an upgrade isn't that much. Going to wait on the scope to get here so i can get the lowest rings.
HDmac is offline  
Old June 7, 2012, 04:14 PM   #6
myshoulderissore
Senior Member
 
Join Date: September 12, 2010
Location: Boise, ID
Posts: 447
Congratulations on your new acquisition, and happy shooting! Sounds like a blast.
myshoulderissore is offline  
Old August 1, 2012, 11:29 PM   #7
browninghunter86
Senior Member
 
Join Date: November 14, 2011
Posts: 524
have you put the base on? How do you like it if you have it installed yet?

I am looking to get a 20 MOA base but do not want to spend a ton on it
browninghunter86 is offline  
Old August 1, 2012, 11:37 PM   #8
HDmac
Member
 
Join Date: May 23, 2012
Posts: 25
Yes, I decided on a Evolution Gun Works Steel HD Savage Short Action Round Back Picatinny Rail Scope Mount - 20 MOA 86202 $102.99

So far it has worked great. I did have to bed it when i first got it (not sure if it was the base or the action that was a little off) It is real solid, nicely made. I can still get a 100 yard zero with the 20 MOA but my scope has lots of adjustment (30mm tube)
HDmac is offline  
Reply

Tags
base , rails , scope , viper , vortex

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 09:59 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07323 seconds with 7 queries