The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Smithy

Reply
 
Thread Tools
Old May 31, 2012, 05:47 PM   #1
the old gringo
Junior Member
 
Join Date: May 31, 2012
Location: fayette MO.
Posts: 13
weaver side mount correct location for jap

been looking at my little 6.5 jap and located in a box of mounts and found a no#1 weaver side mount base i have stayed away from side mounts but with the markings intact and bend of the bolt i think i will try. then how do you locate the base on the action ? i dont want a swiss cheese action, any suggestions? thanks
the old gringo is offline  
Old May 31, 2012, 08:39 PM   #2
DnPRK
Senior Member
 
Join Date: August 24, 2001
Location: LC, Ca
Posts: 1,760
I have several Arisakas and I wouldn't think of drilling the receiver for side or top mounts.

Instead, get an S&K mount that replaces the rear sight leaf.
Click here - and scroll down towards the bottom of the page

With a extended eye relief (pistol) scope and low rings, its what my old eyes need to hit the bullseye at 100+ yards.
DnPRK is offline  
Old May 31, 2012, 09:15 PM   #3
Gunplummer
Senior Member
 
Join Date: March 11, 2010
Location: South East Pa.
Posts: 1,399
I went that route with a 6.5 carbine years ago. What a mistake that was. Putting a pistol mount on for hunting is a joke. Side mounts are hard enough to get used to when hunting. ( I can shoot Lee Harvey, my Carcano pretty good but it took a lot of practice). The only way to scope a rifle correctly is on the top of the receiver. Most of the 6.5 rifles out there still have the mum, but the rest of the parts do not match. If yours is totally matching and has the extras, I would think about not drilling and tapping for a scope. There are plenty of long 6.5's out there that you could cut down.
Gunplummer is offline  
Old June 1, 2012, 10:00 AM   #4
tobnpr
Senior Member
 
Join Date: August 1, 2010
Location: Tampa Bay
Posts: 2,838
Can't speak to the Jap, but I used the Weaver #1 on my Mosin Nagant project rifle- and it worked perfectly. Required me to fab a very low clearance bolt, so pay attention to that if applicable to your rifle.

tobnpr is online now  
Old June 6, 2012, 05:35 PM   #5
Gunplummer
Senior Member
 
Join Date: March 11, 2010
Location: South East Pa.
Posts: 1,399
Side mounts were invented for split-bridge and top exposed bolt guns. Basicly, a last resort to scope a rifle that will not readily accept a scope. Even with a side mount, the Japanese rifles will need some change to the bolt handle. The safety is O.K. even with a top mount set up. What is to gain by using a side mount? You still drill holes in the receiver.
Gunplummer is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 12:46 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.06537 seconds with 7 queries