The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old May 28, 2012, 01:19 PM   #1
freestate101
Junior Member
 
Join Date: May 28, 2012
Posts: 1
Wolf Small Mag Rifle primers in 357 SuperMags?

I have 5K wolf Small Rifle Mag primers left over from the 6BR I used to load for. Is it possible to use these in a 357 Super Mag?

Jim
freestate101 is offline  
Old May 28, 2012, 02:32 PM   #2
Unclenick
Staff
 
Join Date: March 4, 2005
Location: Ohio
Posts: 10,314
Welcome to the forum.

Well, they will fit and they will fire, except maybe if you've got a revolver with soft mainspring. The main thing is that the rifle magnum primer makes a larger volume of gas than either standard rifle or either pistol primer. If it unseats your bullet before the powder gets burning (and it may) there is a chance you will get a squib load, with the powder venting out of the barrel/cylinder gap or backward around an unexpanded case in the chamber, leaving a bullet stuck in the barrel for your trouble. If the gun is a single shot, it may work OK. Typically, these high gas volume primers give higher muzzle velocity extreme spread when used in a case that's too small for their intended purpose.

On the other hand, it may fire OK, in which case you want to be sure your powder charge is reduced 10% to start. The higher pressure in the case, if the bullet doesn't unseat too early, will start the powder burning faster than usual, raising peak pressure some. So you want to start light and work up while watching for pressure signs. I would probably avoid using it with a powder you can't reduce the loads on safely, like H110/296. I would fire only one at a time during workup in a revolver and check to be sure I saw a bullet hole in the target and that nothing was stuck in the barrel before firing again.
__________________
Gunsite Orange Hat Family Member
CMP Certified GSM Master Instructor
NRA Certified Rifle Instructor
NRA Benefactor Member
Unclenick is offline  
Old May 31, 2012, 07:50 AM   #3
WESHOOT2
Senior Member
 
Join Date: February 20, 1999
Location: home on the range; Vermont (Caspian country)
Posts: 14,270
Yes.
__________________
.
"all my ammo is mostly retired factory ammo"
WESHOOT2 is offline  
Old May 31, 2012, 10:04 AM   #4
zxcvbob
Senior Member
 
Join Date: December 20, 2007
Location: S.E. Minnesota
Posts: 4,198
They'll work just like small pistol magnums, it'll just take a harder hit from the firing pin to set them off.
__________________
"The only way to stop a bad guy with a gun is with a good guy with a gun"
zxcvbob is online now  
Old May 31, 2012, 07:37 PM   #5
DWFan
Senior Member
 
Join Date: April 25, 2008
Posts: 213
Small rifle primers are recommended for .357 Maximum loads due to the long column of powder and the pressures the cartridge operates at. I use the CCI #450.
DWFan is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 07:10 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.05511 seconds with 7 queries