The Firing Line Forums

Go Back   The Firing Line Forums > The Hide > NFA Guns and Gear

Reply
 
Thread Tools
Old May 11, 2012, 11:22 PM   #1
madmax1854
Junior Member
 
Join Date: June 6, 2009
Posts: 6
Suppressed SBR AR build advice

I just purchased a Thunderbeast .223A suppressor and an Aeroprecision AR lower to be registered as an SBR, the paperwork is currently getting signed at the Sheriff's office (hopefully).

Its been a while since I've owned an AR, and it was a varminter.

I started looking at options at how to build my lower, it was daunting to say the least. So many options, and I dont know how to seperate the wheat from the chaff. My intent is to have a fun, small, relatively quiet rifle to plink with, maybe hunt some small feral hogs, and definitely keep as one of my SHTF rifles (the main SHTF rifle being my SOCOM II, love it). I want a good, clean trigger, collapsible stock, large charging handle, high quality lower parts kit. I plan on having an 18" upper for long range precision in addition to a shorty upper.

Also, which barrel length would allow the shortest OAL with suppressor while not hamstringing me too much from reduced velocity? I was thinking 10.5-12 inches. And would a 1/7 twist rate be the best? I'd shoot the heavier bullets for hunting, but would also want to be able to shoot cheap 55-62 gr surplus in bulk.
madmax1854 is offline  
Old May 12, 2012, 06:25 AM   #2
David Hineline
Senior Member
 
Join Date: December 23, 1999
Location: South Sioux City, Nebraska
Posts: 703
Have you shot a .223 silencer on an AR/M16 type firearm, the gas blowback from the ejection port is killer if you shoot left handed, most right handed people are ok with it.

I always run a 30 cal silencer on my .223 semi autos cause as a lefty they choke me out.

If I was building it, I would use the MagPlul MOE buttstock 11,5" barrel with a latching QD type silencer.

If you are going to use a thread on silencer, you can use a Nord Lock washer to keep it tight, but will need a glove to routinely check that hot silencer that it has not shook loose on the threads while shooting fast.
David Hineline is offline  
Old May 12, 2012, 07:55 AM   #3
madmax1854
Junior Member
 
Join Date: June 6, 2009
Posts: 6
The thundebeast is a thread on, but thats a good idea about the washer.

Would a "gas buster" charging handle keep the blowback venting down if I use a DI upper? I am right handed.

Thanks
madmax1854 is offline  
Old May 12, 2012, 04:16 PM   #4
David Hineline
Senior Member
 
Join Date: December 23, 1999
Location: South Sioux City, Nebraska
Posts: 703
There is the gas buster charging handle, a company that makes a forward assist button that vents the blowback gas down, all of these things will help. A gas tube or upper with adjustment capabilites will also help.

Look at the website of your silencer, they have a man shooting your silencer choice on a shorty M16, after shooting he wanted gloves and goggles. On your semi auto it will not gas as bad as a full auto does but know it will be there.
David Hineline is offline  
Old May 13, 2012, 04:28 PM   #5
pdogkilr
Member
 
Join Date: March 6, 2012
Location: A little NW of Atlanta
Posts: 47
I went with piston uppers to help with the gas blow-back. Still get some, but not as bad as with DI. I also used 10.5" barrels. That is about as short as I wanted to go and not be abusive to the can. For mounting, I chose the AAC Blackout Muzzle Brake. It has two baffles to take the brunt of the initial fireball. I have one registered SBR lower and two uppers, one in 5.56 the other in 6.8 SPC. Each upper has its' own AAC M4-2000 Mod-8 Suppressor. The system works and is two tons of fun to shoot.
__________________
NRA Patron Life Member
NRA Certified Instructor
pdogkilr is offline  
Old May 29, 2012, 12:02 PM   #6
Rebok87
Member
 
Join Date: December 14, 2009
Location: Columbia,SC
Posts: 60
The W.A.R. receiver will fix that blow back problem.

http://www.gunn-fighter.com/innovati...-receiver.html
Rebok87 is offline  
Old May 29, 2012, 04:29 PM   #7
tepin
Senior Member
 
Join Date: July 14, 2006
Location: MN
Posts: 114
Some Noveske models use a Switchblock (adjustable) to help with suppressed 5.56 AR.
http://noveskerifleworks.com/cgi-bin...status=&title=
tepin is offline  
Old June 4, 2012, 01:32 AM   #8
docpadds
Senior Member
 
Join Date: July 8, 2009
Posts: 125
We have found that we are really beating up the suppressors on the short barrels, especially the 11 and below.
Gas piston is a help when suppressing just for its tunable nature too and does keep some if that crud away from you.
A good muzzle break makes a HUGE difference, honestly until you try a few yiu may not believe it but its true.

My favorite AR we have right now is a 11.5inch one. We usually keep it suppressed just because the thing is so loud. But even in 3 round burst its a decent balance of accurate but still short.
__________________
07 Manufacturer and 02 SOT and 08 Importer.
NRA Certified Instructor Pistol/Rifle. NRA RSO.
Owner of GunEnvy. See our Facebook page for more.
docpadds is offline  
Old June 4, 2012, 07:12 PM   #9
madmax1854
Junior Member
 
Join Date: June 6, 2009
Posts: 6
Thanks for the replies. I decided on a Timney trigger, Magpul UBR stock and grip in FDE. Sent off my paperwork for approval for my suppressor and SBR registration last week. Right now I'm leaning towards a LaRue stealth 12" upper, but might consider an LWRC in 10.5", but apparently I have 6-7 months to think about it while the ATF sits on my papers.
__________________
"Alright you primitive screwheads, listen up. See this? This, is my BOOMSTICK!"
madmax1854 is offline  
Old June 4, 2012, 07:53 PM   #10
FordV8
Member
 
Join Date: February 17, 2011
Location: Southern USA
Posts: 19
I run a 12.5" switchblock Noveske upper. It runs well on everything I've fed it, including bags of mixed up cheap stuff. Its accurate too!

It's long enough keep decent ballistics. Also, I like 11+ inches to stabalize the round, reducing baffle strike.

Yet, it's short enough to be handy even when suppressed.

The switchblock works. I like that you can turn it "off." i.e. single shot only.

I use a Gieselle SSA Trigger in this lower and like it alot. I also have a Timney 3lb single stage in a Mk12 Mod0 and like it just as well. The Timney has better feel but it clearly strikes a little lighter. FWIW, I run AR Gold in my target AR and it's got the best feel yet. I do have a KNS anti walk kit on the Timney.

My experience with LaRue is good as well.

If I were going to "Piston" an SBR, I would choose PWS. Based on theory and second hand knowledge only. <-- grain of salt

I think your setup sounds good and well thought out.
FordV8 is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 08:59 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2013 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.09128 seconds with 7 queries