The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting > Bullet Casting

Reply
 
Thread Tools
Old April 10, 2012, 11:00 PM   #1
deerslayer303
Senior Member
 
Join Date: January 10, 2011
Location: Leesville SC
Posts: 1,392
REAL bullet lube

Hey fellas,
I was reading the instructions that came with the REAL mold. I don't know if these instructions are general for all the molds, but it says coating the entire bullet with alox is better than just lubing the grooves. (may be Lee's ploy to sell Alox). Should I do that or Pan lube the grooves? What has been your experience? The barrel of this .58 is chrome lined so I don't know if it will lead heavily or not with either lube style. Thoughts? Of course I'd rather have pretty red lube in the grooves I was planning on pan lubing with that Gatofeo lube with a couple red crayons thrown in. Can't wait to cast some of these up and try em out. Thanks for all ya'lls help!
__________________
"I prefer dangerous freedom over peaceful slavery."
- Thomas Jefferson
deerslayer303 is offline  
Old April 11, 2012, 09:09 AM   #2
Rangefinder
Senior Member
 
Join Date: August 4, 2005
Posts: 2,017
Do the whole thing same as a cartridge bullet. It's a very thin layer you're looking for anyway.
__________________
"Why is is called Common Sense when it seems so few actually possess it?"

Guns only have two enemies: Rust and Politicians.
Rangefinder is offline  
Old April 11, 2012, 07:48 PM   #3
dickttx
Senior Member
 
Join Date: May 29, 2011
Location: Fort Worth
Posts: 500
Lee was probably looking to get rich on the alox they buy from someone else.
__________________
Education teaches you the rules, experience teaches you the exceptions (Plagiarized from Claude Clay)
dickttx is offline  
Old April 11, 2012, 08:23 PM   #4
mikld
Senior Member
 
Join Date: February 7, 2009
Location: Southern Oregon!
Posts: 1,182
Alox (or xlox where I buy it) works quite well for me in lower pressure loads. For my magnum loads I usually use a high pressure/velocity lube. I'm sure the alox lube will work on a large, slow bullet. A 4 oz. bottle of Lee alox will last for several hundred in not thousands of bullets so I highly doubt if anyone can get rich from selling it. A little goes a loooooooong way.
__________________
My Anchor is holding fast!
mikld is offline  
Old April 30, 2012, 10:04 PM   #5
458winshooter
Senior Member
 
Join Date: June 16, 2008
Location: Louisville,Tn
Posts: 416
Lee REAL

I have read that some folks claim alox and blackpowder don't mix well so I started looking for a lube since I bought my first muzzleloader last year.They claim that "Bore Butter"can be used as a lube but I didn't have much luck so what I did was make my own.Equal parts of beeswax and crisco melted together.
458winshooter is offline  
Old May 1, 2012, 05:18 AM   #6
PawPaw
Senior Member
 
Join Date: December 24, 2010
Location: Central Louisiana
Posts: 3,115
At black powder velocities, almost anything will work, including hog lard. My BP lube is hog lard and beeswax. Junior uses a little alox, but I don't see the benefit. I mix a 3:1 ratio or maybe a little less beeswax, depending on how hard I want the lube to be.

Like I said, though, at BP velocities anything will work. If you simply want to tumble them in Alox, that'll work too. Which reminds me, I need to order some Xlox.
__________________
Dennis Dezendorf

http://pawpawshouse.blogspot.com
PawPaw is offline  
Old May 1, 2012, 06:24 AM   #7
mehavey
Senior Member
 
Join Date: June 17, 2010
Location: Virginia
Posts: 3,065
50/50 ALOX/Beeswax (in round sticks for the lubrisizer) is the classic cast bullet lube

Shooting NSSA for many, many, many years, my preferred BlackPowder lubes
(where firing rates were high/keeping fouling soft was critical) were:

Zouave Musket: 3:1 Crisco/50-50

Enfield Musketoon
- Winter 3:1 Crisco/50-50
- Summer 4:1:1 Crisco/50-50/StraightBeeswax

1861 Colts Special Model (Original)Musket: 3:1 Crisco/50-50

1860 Army and `51 Navy: Lithium Grease

`63 Sharps Carbine: (both Buffalo Slug & NEI Conical) 3:1 Crisco/50-50 (lots of it)
mehavey is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 04:54 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07438 seconds with 7 queries