The Firing Line Forums

Go Back   The Firing Line Forums > The North Corral > Curios and Relics

Reply
 
Thread Tools
Old April 3, 2012, 12:16 PM   #1
jallenbet
Junior Member
 
Join Date: April 3, 2012
Posts: 4
Springfield 1898

Hi guys I am brand new to this forum. I joined because I just purchsed a Springfield 1898 30-40 Krag. I don't really know anything about it. There is an S stamped on the barrel about half way down. Where else should I try to find another stamp like this? I'm also missing alot of parts like the front and back sights, the butt of the stock, and the knob on the bottom of the stock. I don't think this is the original stock? I haven't seen it in any of the pics during my research. The barrel is about 22 1/2" long from end to end including the threads. I know the little slot toward the end is for the front sight, but a few inches back there is a small hole drilled off center. It's not tapped and is not that deep. Any ideas on what it might have been for? Any info would be much appreciated! I would love to complete this gun. Is there any place local I might find parts and is this gun actually worth anything? Thanks guys!
jallenbet is offline  
Old April 3, 2012, 02:08 PM   #2
viciouskitty
Senior Member
 
Join Date: August 6, 2010
Location: South Texas
Posts: 260
I would look up numrich gun parts on the web. Krag parts are not that common but if you keep looking up places like gun broker and ebay you may find what you need. It may not be cheap though, I myself love recusing old rifles that have been abused by their owners. I restored a lee enfield back to military trim after it had been painted and hacked to death. It even had a glued on scope mount, now it looks pretty again goodluck in your pursuit there.
viciouskitty is offline  
Old April 3, 2012, 02:26 PM   #3
jallenbet
Junior Member
 
Join Date: April 3, 2012
Posts: 4
Repost - Springfield 1898

Photos added.
Attached Images
File Type: jpg IMG_1362.JPG (93.3 KB, 38 views)
File Type: jpg IMG_1363.JPG (71.4 KB, 29 views)
File Type: jpg IMG_1365.JPG (109.8 KB, 27 views)

Last edited by Mike Irwin; April 5, 2012 at 04:48 PM. Reason: Merged threads.
jallenbet is offline  
Old April 3, 2012, 07:32 PM   #4
30-30remchester
Senior Member
 
Join Date: April 18, 2009
Location: mountains of colorado
Posts: 977
I have been fond of these classic guns and have had a number of the over the years and have done some research as well. Well first off you have an 1898 Springfield rifle known as a US Krag. Your purchase is a rifle that has started to be sporterised. The stock is not original. The sights are missing as well as you know. The hole drilled off center in the barrel is a puzzle to me, about the only thing I know about it, is it is not factory original. About the only thing to do is finish the stock and put sights back on it, then enjoy the shooting. Sights are available regularly on EBAY.
30-30remchester is offline  
Old April 4, 2012, 04:31 PM   #5
Scharfschuetzer
Senior Member
 
Join Date: January 28, 2012
Location: Puget Sound
Posts: 293
Jallenbet,

That looks like it will be quite the project. To be honest, in the end, it may cost more than what it's worth. I'm sure it would be fun to restore to shooting condition though.

Krags used a single heat treatment process and as a result, cracks in the single locking lug on the bolt have been reported in several publications over the years. On the other hand, they have a glass smoth action and the calibre is certainly an effective deer load within reasonable ranges. In the event of a bolt sheering off, the base of the bolt handle provides a large safety lug.

I have no idea if your rifle was cut down from the infantry rifle or is from a carbine. Either way, I'm pretty sure that the front sight was brazed on with the original barrels. I'm not sure about the rear sight as the previous US rifle, the Trapdoor had it's rear sight screwed on with two headless screws. I can't check mine right now as I'm traveling, but that's what my memory is telling me. If that is in fact so, then the drilling and tapping at the front was done by whoever had the weapon before. The odd hole you mention was not on any US military rifle that I know of.

I have a Krag and keeping in mind paragraph two, I just shoot cast bullets out of it. With good bores, they are great fun and shoot quite well.



P.S. Have you figured out how to remove the bolt yet?
__________________
Scharfschuetzer
US Army Distinguished Rifleman
Washington State Distinguished Rifleman
NRA Police Distinguished Expert

Last edited by Scharfschuetzer; April 5, 2012 at 03:00 PM.
Scharfschuetzer is offline  
Old April 5, 2012, 03:55 PM   #6
jallenbet
Junior Member
 
Join Date: April 3, 2012
Posts: 4
Thanks for the info guys. Much appreciated! I did get the bolt apart.
jallenbet is offline  
Old April 5, 2012, 04:47 PM   #7
Mike Irwin
Staff
 
Join Date: April 13, 2000
Location: Northern Virginia
Posts: 35,251
Welcome to TFL.

Please do NOT post the same message to multiple forums. It dilutes the discussion.

I've merged your two threads together, but in the future, if you'd like a thread moved, please contact one of the staff members for the forum that either it is then in, or the forum where you would like it to go.
__________________
"The gift which I am sending you is called a dog, and is in fact the most precious and valuable possession of mankind" -Theodorus Gaza

Baby Jesus cries when the fat redneck doesn't have military-grade firepower.
Mike Irwin is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 08:07 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2013 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07508 seconds with 10 queries