The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Harley Nolden Memorial Institute for Firearms Research

Reply
 
Thread Tools
Old November 17, 2000, 07:59 PM   #1
tatters
Senior Member
 
Join Date: October 16, 1999
Location: Indiana
Posts: 786
One of my co-workers asked me to do a little research for him. He has an old muzzleloader and it is as such:

I think it is a Kentucky Longrifle or Pennsylvania Rifle

32 1/2 long, rifled (I think), heavy, octagonal barrel. It appears as though there are some sort of dimples on the bottom like they are flashings from a mold. Cap and ball , set triggers (if I know what that really means). Does that mean you pull the curved trigger so the hammer will engage and then pull the straight trigger to fire? Anyway, it has a severely curved brass buttplate and a cheek rest. The sights are dovetailed, but the rear sight is gone. The forearm extends to about halfway up the barrel and has a cap on the muzzle end, and the ramrod goes in the forearm cap and into the forearm. The diameter of the bore is about 3/8 inch.
It has a brass trigger guard with curved finger rests on the bottom that extend about an inch.The steel lockplate(?) is engraved with a a pointer dog pointing at some unknown animal. It also has leaves and grasses engraved on the plate surrounding the scene.

It is engraved with the words: g.g. julcher ( I think)

Any Ideas what this thing is?

[Edited by tatters on 11-17-2000 at 08:32 PM]
__________________
" When you've been granted the privilege of being heard..take great care with this power and watch every word"
tatters is offline  
Old November 17, 2000, 09:26 PM   #2
Mike Irwin
Staff
 
Join Date: April 13, 2000
Location: Northern Virginia
Posts: 35,651
Tatters,

The name may actually be Gulcher...

For some reason, that rings a bell. I've got a good book on rifles of this genre around here somewhere.

Let me dig it up, and I'll try to find something about it.

You are, though, describing a pretty typical rifle of this type.

Your thoughts on the set trigger are, I believe, right on.
Mike Irwin is offline  
Old November 17, 2000, 10:27 PM   #3
Mike Irwin
Staff
 
Join Date: April 13, 2000
Location: Northern Virginia
Posts: 35,651
Tatters,

Not too much information, I'm afraid.

I THINK that the lockplate on your gun was made by James Golcher of Philadelphia.

My book unfortunatly has very very little information on him, only listing him as being in Philadelphia in 1855/1861. It doesn't give a reference for that information (such as tax lists, business directories, etc.)

And, that information doesn't seem to square with an illustration earlier in the book showing a Golcher lock in an early 1800s flint style.

Your friend may want to write to or contact the Philadelphia Historical Society, or the Pennsylvania State Museum & Historial Commission for more information.
Mike Irwin is offline  
Old November 18, 2000, 08:40 AM   #4
fal308
Staff Alumnus
 
Join Date: October 12, 1998
Location: Missouri
Posts: 1,986
Most gunmakers bought their locks instead of building their own. It was a matter of economy, among other things. The markings on the lock only indicate who made the lock, usually not the whole firearm. That said...
"The Golchers were a family of gunlock makers in the early nineteenth century. There were at least five members of this family. One of them, Joseph, eventually emigrated to California and opened a shop there.
At least two of the Golcher family, James and John, were riflesmiths, but their names and those of others of the same family are found on a great number of locks of old rifles known to be the work of many makers. This may account for the numerous so-called Golcher rifles. James Golcher branded his name on both his barrels and locks. The author has knowledge of only one of his guns. John Golcher doubtless made many rifles, but there is no credible evidence that others of that family were extensive makers."
The above information is from The Kentucky Rifle by Captain John G. W. Dillin
fal308 is offline  
Old November 20, 2000, 05:43 AM   #5
4V50 Gary
Staff
 
Join Date: November 2, 1998
Location: Colorado
Posts: 16,542
Mind you though that as guns were used and worn, they were salvaged for parts. Thus, a lock from England could find itself mated with an American barrel made in Tennessee and a trigger guard casted in Ohio with the stock and fitting done by some gunsmith in Kansas!

A more thorough examination of the gun is required to see whether the style and workmanship matches that of a particular gunsmith.
4V50 Gary is offline  
Old November 20, 2000, 09:23 AM   #6
Cap n ball
Senior Member
 
Join Date: October 17, 2000
Posts: 247
Golcher, as said previously was a name associated with a Pennsylvania family of locksmiths from the mid 18th to mid 19th century. Now, I'm sure there were exceptions but their product was mainly a very ordinary affair used on common firearms such as would be purchased by folks at general stores and such. Your description fits what they called a fowling piece. Probably smooth bore and around 12ga. with hunting dogs engraved on it. Most were flinters with some being converted after percussion caps came into use. A converted piece is usually not as prized as an original. The wood used was not the best quality. These pieces were clearly intended to satisfy the family farm market. I haven't seen any listed as worth more than a few hundred dollars. I'd call it a wallhanger. I would not suggest that it be fired under any circumstances. Sometimes these old things are still loaded and old loads have been known to still ignite after a very long time. Make sure that the bottom of the bore is clear.
Cap n ball is offline  
Old November 20, 2000, 05:11 PM   #7
James K
Staff
 
Join Date: March 17, 1999
Posts: 19,087
By that time, very few gunsmiths were actually making anything but stocks, and even those were available roughly inletted. Barrels, furniture and locks were bought from outfits like J&D Little in Pittsburgh. The lock you describe sounds like a typical English lock, turned out by the thousands in Birmingham and sold all over the world. Many are marked "Warranted", though they don't say by whom or how a claim can be made if the product is defective. (Sound familiar?)

The caliber indicates it is a small bore rifle for deer and smaller game or for target shooting. Value is hard to judge, and there are many variations. Percussion rifles generally bring less than flintlocks and average $2-3000 in top condition. Obviously, rust, broken stocks, other broken parts, etc. will reduce the value considerably.

One interesting thing to check - many of the rifles of that era have straight rifling. I don't know why.

Jim
James K is offline  
Old November 20, 2000, 11:08 PM   #8
tatters
Senior Member
 
Join Date: October 16, 1999
Location: Indiana
Posts: 786
I looked again, guys, and I am almost positive the name is Julcher. It is fairly clean, and unmarred.
Any other thoughts?
tatters is offline  
Old January 15, 2005, 11:30 AM   #9
Flexmoney
Member
 
Join Date: April 25, 2002
Location: Ohio (Columbus, McConnelsville)
Posts: 23
I also have one that I'd like to get some info on.

The lock of this one reads "G. Gulcher"

The top of the barrel seems to read "J.F. VANTREES"

?

Where is the market for these?
__________________
Have fun,
Kyle
Flexmoney is offline  
Old January 15, 2005, 12:32 PM   #10
4V50 Gary
Staff
 
Join Date: November 2, 1998
Location: Colorado
Posts: 16,542
Vantrees could be the fellow who assembled the gun. By the mid-1800s, both barrel & lock could be bought and the gunsmith need only assemble the parts to make a gun. Many gunsmiths still could and did make their own barrels and casted their own parts (trigger guard, buttplate, sideplates, nose caps)>
__________________
Vigilantibus et non dormientibus jura subveniunt. Molon Labe!
4V50 Gary is offline  
Old January 3, 2006, 06:48 AM   #11
ghulse
Junior Member
 
Join Date: January 3, 2006
Location: cedar run, pa.
Posts: 1
to Tatters r:golcher long rifle

In search for info on a Kentucky rifle I have, I came across this article in FiringLine. I imeadiately signed up. The rifle I have is marked "Jas. Golcher/Lancaster". It is a .30 cal. rifled bore' octegon bbl. Overall length is 54", bbl. is 38.5". The stock is fancy tiger maple, with 20 pcs. of silver inlay and brass patch box. It has a severe curved brass butt plate, the trigger guard is brass with curved finger grip. It has a set trigger, and is percussion. Condition is " fair to good " by NRA standards. I'll be able to post a picture soon. I'd like a reply with any info anyone may have.
ghulse is offline  
Old January 3, 2006, 10:04 AM   #12
deadin
Junior member
 
Join Date: September 6, 2005
Location: Ocean Shores, WA
Posts: 1,052
I would guess these are possibly what is known as a "Ohio Halfstock Percussion Sporting Rifle" See Flayderman's "Guide to Antique American Firearms", Chapters XI and XII for a discussion on the differences between Kentucky, Pennsylvania and Ohio rifles.

Dean
deadin is offline  
Old April 27, 2009, 12:11 PM   #13
AVanTrees
Junior Member
 
Join Date: April 27, 2009
Location: Berne,IN
Posts: 2
VanTrees Guns

I new here...I seen the message about the J F Vantrees Stamp on the barrel of the gun. My new husband great great grandfather was the gun maker J F VanTrees. I would like to find some of these guns to give him as a gift. If anyone has them for sale or know where I could get some. Please let me know. If you want to know any info on them I'll try to find that out for you.
AVanTrees is offline  
Old April 27, 2009, 01:48 PM   #14
Flexmoney
Member
 
Join Date: April 25, 2002
Location: Ohio (Columbus, McConnelsville)
Posts: 23
The one I posted about belongs to an in-law that asked about it.

Any info you coild come up with would be great!
__________________
Have fun,
Kyle
Flexmoney is offline  
Old April 27, 2009, 03:17 PM   #15
AVanTrees
Junior Member
 
Join Date: April 27, 2009
Location: Berne,IN
Posts: 2
Hope this helps.

The JF VanTrees guns were made in Fort Recovery,Ohio. I was told That JF made every gun stock to fit the person that the gun was made for. My husband actually has the JF Vantrees gun stamp. If you look up VanTrees in Fort Recovery Ohio there is an article all about the guns. There is also the VanTrees park in Fort Recovery. If they would ever want to sell the gun I might be interested in buying it.

Angel
AVanTrees is offline  
Old April 27, 2009, 08:09 PM   #16
Flexmoney
Member
 
Join Date: April 25, 2002
Location: Ohio (Columbus, McConnelsville)
Posts: 23
Angel,

I'm having trouble locating an article on that. Is it on the internet? Can you point me to a link?

Everything I find on Ft. recovery points me to an earlier period...that of the North West (Ohio) Territory. Which would seem to pre-date this gun by 50-60 years.
__________________
Have fun,
Kyle
Flexmoney is offline  
Old March 13, 2012, 09:41 AM   #17
USMC-Grunt
Junior Member
 
Join Date: March 13, 2012
Posts: 7
J F Vantrees rifle found in Michigan.

Hello,
I just purchased an old JF Vantrees Full stock rifle out of a barn being cleaned out in Southern Michigan and found this thread so I thought I would add to it. I've found some interesting information about the builder but would like to learn more. Not really into collecting these so don't have much knowledge in this area (I collect mainly militaria WWI to Vietnam).
I will add pics here in just a minute.
Thanks and nice forum you have here!!
Troy
USMC-Grunt is offline  
Old March 13, 2012, 10:03 AM   #18
USMC-Grunt
Junior Member
 
Join Date: March 13, 2012
Posts: 7
J F Vantrees rifle found in Michigan

Here are some pics. It's just as found, all I've done for now is tie a piece of leather strap around the muzzle to hold the barrle onto the stock as the retaining pis are missing. The barrel looks unfinished underneath and hand forged. The unique thing is the "J F Vantrees" marking is on the bottom of the stock? Could this be an early one of his maybe?
Attached Images
File Type: jpg Vantrees long rifle 021.jpg (37.3 KB, 31 views)
File Type: jpg Vantrees long rifle 025.jpg (50.5 KB, 28 views)
File Type: jpg Vantrees long rifle 023.jpg (51.3 KB, 27 views)
USMC-Grunt is offline  
Old March 13, 2012, 10:05 AM   #19
USMC-Grunt
Junior Member
 
Join Date: March 13, 2012
Posts: 7
J F Vantrees rifle found in Michigan

More pics
Attached Images
File Type: jpg Vantrees long rifle 018.jpg (49.3 KB, 26 views)
File Type: jpg Vantrees long rifle 019.jpg (51.1 KB, 24 views)
File Type: jpg Vantrees long rifle 020.jpg (50.6 KB, 26 views)
USMC-Grunt is offline  
Old March 13, 2012, 10:07 AM   #20
USMC-Grunt
Junior Member
 
Join Date: March 13, 2012
Posts: 7
J F Vantrees rifle found in Michigan

Last ones.
Thanks
Attached Images
File Type: jpg Vantrees long rifle 022.jpg (52.4 KB, 26 views)
File Type: jpg Vantrees long rifle 027.jpg (51.4 KB, 23 views)
File Type: jpg Vantrees long rifle 029.jpg (39.2 KB, 25 views)
USMC-Grunt is offline  
Old March 13, 2012, 10:28 AM   #21
mapsjanhere
Senior Member
 
Join Date: August 6, 2009
Location: Albuquerque
Posts: 2,342
You might be right on the hand-forged, with that drum and nipple style lock it looks like a flint-to-percussion adapted barrel. What's the caliber?
__________________
F 135 - the right choice
mapsjanhere is offline  
Old March 13, 2012, 10:51 AM   #22
USMC-Grunt
Junior Member
 
Join Date: March 13, 2012
Posts: 7
I'm not sure on the Cal. but I can see rifling. When I dropped the ram rod down the barrel it shot out a nice big ploom of dust!!
USMC-Grunt is offline  
Old March 13, 2012, 10:56 AM   #23
USMC-Grunt
Junior Member
 
Join Date: March 13, 2012
Posts: 7
From what I've read this was a builder out of the Fort Recovery Ohio area and built his guns from 1854 to 1890. The Great-Grandsons still have his rifling tools. I was hoping to contact a relative.
If you look close at the hammer and cap area you can see a flash pan or shield?? I was told this might mean it was placed there for a left handed shooter? Does that sound right?
USMC-Grunt is offline  
Old March 13, 2012, 11:37 AM   #24
Hawg Haggen
Senior Member
 
Join Date: September 8, 2007
Location: Mississippi
Posts: 11,617
Very nice for a barn find. My WAG on the caliber is .32, hard to tell from a pic tho.
Hawg Haggen is offline  
Old March 13, 2012, 11:45 AM   #25
USMC-Grunt
Junior Member
 
Join Date: March 13, 2012
Posts: 7
Thanks,
The bore seams to measure approximately 1/2" across if that helps. Yes I think it looks pretty good. Could use a coat of oil and some retention pins (if that's what they're called. The locking loops under the barrel are fine so they must have just been removed and lost or fell out??
USMC-Grunt is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 05:21 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.14873 seconds with 10 queries