The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Smithy

Reply
 
Thread Tools
Old March 20, 2012, 11:27 AM   #1
Northern Gal
Member
 
Join Date: April 5, 2011
Posts: 29
Need help w/ reassembling my new EMP

Please move this if this isn't the proper place to post.

I bought a Springfield EMP this weekend, so I went on You Tube and watched a great video on how to disassemble and reassemble it. I took it down and cleaned it just fine yesterday, but I can't get the slide stop back in during reassembly. I line it up w/ the hole on the barrel and start sliding it in, however, I can't get the right hand side of the slide stop to push in - it seems like the slide stop is too long (which, of course, I know it isn't). What am I doing wrong? All suggestions are very welcome.
Northern Gal is offline  
Old March 20, 2012, 01:02 PM   #2
john323
Member
 
Join Date: June 16, 2009
Location: MONTEREY PARK , CA
Posts: 74
Do you have it lined up with the notch on the slide?
__________________
johnsgunsmithing@live.com

Southern California
Anything legal, Rifles, Handguns, Shotguns, Black powder
john323 is offline  
Old March 20, 2012, 01:11 PM   #3
CowTowner
Senior Member
 
Join Date: October 17, 2007
Location: Cowtown of course!
Posts: 1,147
It should look something like what is shown in the attached picture
Attached Images
File Type: jpg reass06.jpg (65.5 KB, 14 views)
__________________
NRA Chief Range Safety Officer, Home Firearm Safety and Pistol Instructor
"There are three classes of people: those who see, those who see when they are shown, those who do not see."
Leonardo da Vinci
CowTowner is online now  
Old March 20, 2012, 02:07 PM   #4
Northern Gal
Member
 
Join Date: April 5, 2011
Posts: 29
CowTowner: The problem I'm having is that the right edge will not fit to slide down under the notch in the slide - it hits that piece on the right that butts up to it when it's in place correctly. I'm obviously doing something wrong such that the hole that lines up w/ the barrel for the slide stop to go into is just a bit too far right. (Does that make sense?)
Northern Gal is offline  
Old March 20, 2012, 02:38 PM   #5
ScottRiqui
Senior Member
 
Join Date: January 27, 2010
Location: Norfolk, VA
Posts: 2,905
The "piece on the right" is a spring-loaded plunger. It *will* move out of the way to let the slide stop pin snap into place, but it can be a little tricky, especially with a new gun, or with a shooter that's not used to the procedure. Make sure you apply force inward and slightly upward (toward the slide). If you press downward, the slide stop pin will rotate clockwise and give you a nice scratch from the plunger to the trigger guard opening.
ScottRiqui is offline  
Old March 20, 2012, 02:48 PM   #6
Northern Gal
Member
 
Join Date: April 5, 2011
Posts: 29
Thanks so much - this is very helpful! I'd like to take it out again tomorrow after work, so I really want to get this figured out.
Northern Gal is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 01:30 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07782 seconds with 10 queries