The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old March 5, 2012, 07:16 PM   #1
enstorm
Senior Member
 
Join Date: August 11, 2005
Posts: 197
RCBS Little Dandy

I bought this measure with the No.10 rotor since the chart says it drops 6.9 grains of power pistol, the load I use for my .40s. I set it up and it isnt close, usually around 6.5 grains. The No. 11 rotor is rated at 7.5 grains for this powder, and it was generally right on the 6.9 grain mark. Am I messing something up?
enstorm is offline  
Old March 6, 2012, 12:52 AM   #2
Scharfschuetzer
Senior Member
 
Join Date: January 28, 2012
Location: Puget Sound
Posts: 293
No, I don't think so.

I had one back in the early 80s and I had to buy several of the little powder drums in order to get the proper weight of powder for the various pistol loads that I was loading for. While the chart that came with it was close for me; it wasn't exact and it took some experimenting with a scale to get the proper drum for the charge I wanted.

Good move on your part to confirm the drum's throw with a scale before trusting it.
__________________
Scharfschuetzer
US Army Distinguished Rifleman
Washington State Distinguished Rifleman
NRA Police Distinguished Expert
Scharfschuetzer is offline  
Old March 6, 2012, 03:42 AM   #3
old roper
Senior Member
 
Join Date: June 11, 2007
Posts: 1,069
enstorm, Here something for instruction I got with Little Dandy,

Warning. Keep in mnid volume/weight ratios may sometimes vary with different lots of same powder. Again check powder charge on an accurate powder scale before charging cases".
__________________
Semper Fi
Vietnam
VFW
old roper is offline  
Old March 6, 2012, 06:06 AM   #4
sourdough44
Senior Member
 
Join Date: October 17, 2007
Location: WI
Posts: 608
There is a guy here 'Bailey Boat' from SC or so that sells an adjustable rotor for the little dandy powder measure. I have one & it works GREAT. I recently loaded up some 380acp rounds & I found the bottom of the adjustment, 3.2 grains of win 231. Most of my handgun charges are a bit higher, so no problem.

I would search out this member & ask about the adjustable rotor for the LD. It's a quality upgrade & greatly improves usefullness of the measure. It is very consistant with the powder drops once properly setup.
sourdough44 is offline  
Old March 6, 2012, 09:36 AM   #5
F. Guffey
Senior Member
 
Join Date: July 18, 2008
Posts: 2,638
Yes, it has been a while since we have seen a round of commercials for the after market adjustable rotor, I thought it was about time for another round.

I could call RCBS and suggest a way to improve the design of the Little Dandy, but, we got a deal, when they need help, they will call.


F. Guffey
F. Guffey is offline  
Old March 6, 2012, 09:41 AM   #6
F. Guffey
Senior Member
 
Join Date: July 18, 2008
Posts: 2,638
For pistol, the Little Dandy is my first choice, I start with the chart, choose the rotor, I do not start with a load then start looking for a rotor I do not have, on occasions I use the Little Dandy for rifle, instead of once, I rotate the rotor twice.

F. Guffey
F. Guffey is offline  
Old March 6, 2012, 10:42 AM   #7
MADISON
Senior Member
 
Join Date: January 1, 2000
Location: Roanoke, Virginia
Posts: 2,678
RCBS Little Dandy Roters

I have been reloading since 1970.
I have the Hornady version, that requires roters. You need the complete
selection of roters. Most of what is published is short on what they
throw. You must try each one to get "as close" to what you want as
possible.
MADISON is offline  
Old March 6, 2012, 05:28 PM   #8
SIGSHR
Senior Member
 
Join Date: September 13, 2005
Posts: 3,074
Yes variations-remember, we are dealing very tiny amounts-will appear, my experience with RCBS products has been that their quality control is excellent so manufacturing flaws can be ruled out.
I recall an article by Dean Grennell where he said he set his adjustable powder measures so that when 10 thrown loads weighed exactlly 10 times the load desired, the measure was correctly adjusted.
SIGSHR is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 05:31 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07053 seconds with 7 queries