The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Gear and Accessories

Reply
 
Thread Tools
Old April 17, 2012, 03:30 PM   #1
Psychbiker
Member
 
Join Date: April 13, 2010
Posts: 27
Driling into Fire Proof Safe -- Pegboard Interior

I have an old double door military safe. Its probably 1500lbs and a 2 hour fire rating.....when new. Not sure if the 2 hour is still the case.

I was thinking about hanging pegboard on the doors the be able to hang guns and what not. My door do not have panels so I would have to screw into the interior of the door.

Good idea or bad idea? Will this affect the fire protection of the safe?

I could figure out how to secure the carpeting for velcro I suppose.
Psychbiker is offline  
Old April 17, 2012, 10:25 PM   #2
Yung.gunr
Senior Member
 
Join Date: November 11, 2010
Location: Phoenix area
Posts: 1,377
What do you plan on putting on the pegboard? I would not drill into it... Those 3M command adhesive strips are amazingly strong. Plus, I'm sure there is stronger stuff. If it is not going to be too heavy I would use some kind of adhesive.

That's just me though...
Yung.gunr is offline  
Old April 17, 2012, 11:33 PM   #3
a1abdj
Senior Member
 
Join Date: November 28, 2005
Location: St. Charles, MO
Posts: 496
Do you have a photo of what you're talking about?

If you're talking about drilling into the insulation itself, it will not hold much weight (if any at all). The fill material in a typical document safe is fairly soft.
__________________
www.zykansafe.com
a1abdj is offline  
Old April 26, 2012, 06:45 PM   #4
UtopiaTexasG19
Senior Member
 
Join Date: July 3, 2011
Location: S.E. Texas Gulf Coast
Posts: 743
There are numerous adhesives on the market with industrial strenght that would easily hold the peg board and weight added. Go to your local big box store and look into "Liquid Nails" or something similiar...
UtopiaTexasG19 is offline  
Old April 26, 2012, 08:04 PM   #5
Fishing_Cabin
Senior Member
 
Join Date: February 10, 2010
Posts: 716
I agree with others it would not be a wise idea to drill into the safe. If it use a steel liner of a good thickness it may not be an issue, but if it has no liner, or it is to thin, it is a problem. I prefer not to drill a safe at all for mounting anything.

I would look for adhesive of some sort, clean the area well, and install the pegboard.
Fishing_Cabin is offline  
Old April 26, 2012, 09:56 PM   #6
kilimanjaro
Senior Member
 
Join Date: November 23, 2009
Posts: 1,902
I've been using Liquid Nails and Liquid Steel for decades, indoors and out. You can mount your pegboard on 3 or 4 metal horizontal strips, then glue the metal to the metal. It will hold. Sink the bolt heads.

If the safe interior is still attractive, I would not use the pegboard. Instead, get a sheet of 3/8" hardwood plywood, cut to fit, glue on a wood strip around the edge, drill your custom hole pattern, insert wood pegs, and stain/finish it up nicely, then mount as above. You'll get more enjoyment out of it, too.
kilimanjaro is offline  
Old April 27, 2012, 01:59 PM   #7
Psychbiker
Member
 
Join Date: April 13, 2010
Posts: 27
I sort of did that but used 3/4 melamine and pieced it together. Counter sunk some screws so when I wrap it with felt its clean. Of course my father who is a contractor wants to tear it all out and start over but then my time and $20 in wood will be tossed away. I plan on covering it felt tonight.
Attached Images
File Type: jpg DoorsOpen.jpg (17.3 KB, 18 views)
Psychbiker is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 05:52 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.06883 seconds with 10 queries