The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Smithy

Reply
 
Thread Tools
Old February 11, 2012, 10:09 PM   #1
WookieRookie
Senior Member
 
Join Date: November 24, 2010
Posts: 105
Oil after a detail strip

Good evening guys. This evening I got bored and detail stripped and cleaned my Springfield XD9. The frame was filthy, and I am glad I did it. My question is, are there any parts that I should reapply oil? I clean the gun religiously any time I fire a round. There appeared to be a lot of oil/gunk on and around the firing pin. I usually oil lightly on the rails, and the barrel. Thanks for any advice.
WookieRookie is offline  
Old February 12, 2012, 02:22 AM   #2
mete
Senior Member
 
Join Date: June 14, 2004
Location: NY State
Posts: 5,491
Firing pin ,spring and hole and extractor ,spring and hole seem to often be forgotten when cleaning.
When parts move against each other they should be lubed with a good gun oil. Lightly lube don't overdo as the oil then attracts dirt.
__________________
And Watson , bring your revolver !
mete is offline  
Old February 12, 2012, 09:49 AM   #3
hooligan1
Senior Member
 
Join Date: July 18, 2010
Location: Independence Missouri
Posts: 3,452
Wookie, I use a product called G-96 gun treatment/ spray lube, and without a doubt it works beautifully. I just sray it on my guns, and scrub with a tooth-brush, wipe of excess completely, then I respray again like the bolt and the mainspring/ trigger group, and then I use my air compressor to blow out all excess oil, and like I said it works beautifully!!
__________________
Thanks for coming!
hooligan1 is offline  
Old February 13, 2012, 10:22 AM   #4
madcratebuilder
Senior Member
 
Join Date: November 2, 2007
Location: Northern Orygun
Posts: 4,871
I treat all metal surfaces with Eezox. Instead of oil on the slide rails, try some Tetra lube.
madcratebuilder is offline  
Old February 22, 2012, 08:47 AM   #5
sarg1c
Junior Member
 
Join Date: February 19, 2012
Posts: 3
Oil after a detail strip

when appling oil to a firearm, use an old shaving brush or equiv. Very soft. A soft brush will not apply oil heavy, leaving a very light coating, especially a carry weapon or one to use in extreame cold weather. The brush will get to areas almost impossible to reach. I always wipe with a dry rag after oiling.this always helped pass inspections in the army...
sarg1c is offline  
Old February 22, 2012, 09:10 AM   #6
BRE346
Senior Member
 
Join Date: February 11, 2011
Location: Victoria, TX
Posts: 158
Oil, except firing pin

Not the firing pin? Yes, but with a dry lubricant, like powdered graphite.

One; it doesn't collect gunk like oil does.
Two; It's slicker.

The firing pin and its chamber are pretty tightly fitted. And the firing pin hole is small, so all that doesn''t need cleaning every time you go to the range.

Just my 2 cents.
__________________
Ancient Airman
BRE346 is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 12:37 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.06610 seconds with 7 queries