The Firing Line Forums

Go Back   The Firing Line Forums > Hogan's Alley > Handguns: The Revolver Forum

Reply
 
Thread Tools
Old February 5, 2012, 03:32 PM   #1
jakeLC
Member
 
Join Date: July 26, 2011
Location: Plainfield, IN
Posts: 49
whats the difference between 999 and 922

i have been looking at .22 revolvers for a little while but am wondering whats the difference between a h&r model 999 and 922. i cant figure it out and was wondering if anyone here could help
jakeLC is offline  
Old February 5, 2012, 03:39 PM   #2
zippy13
Senior Member
 
Join Date: August 23, 2008
Location: SoCal
Posts: 6,392
77
zippy13 is offline  
Old February 5, 2012, 03:58 PM   #3
32 Magnum
Member In Memoriam
 
Join Date: January 17, 2009
Location: Eastern PA
Posts: 364
JakeLC,
The H&R Model 922 is a solid frame, pull-pin for cylinder removal, SA/DA, 9 shot .22lr revolver. It originated circa 1925-26 from the solid frame H&R Model 1904. This model was in the H&R catalogues in at least three models and about a dozen variations up to the early 1980's. The 922 was extremely popular during it's production life, due to value for cost and was a "utilitarian" plinker, hiking/camping piece.
The H&R Model 999 Double Action SPORTSMAN is a hinged frame, break open, auto ejecting, DA/SA 9 shot .22 lr revolver. It originated after Oct. of 1932 and was loosely based upon the H&R USRA Model 195 Single shot target pistol. There are three recognized models and about a dozen variations made up to Jan. 1986 and then again by NEF from 1987 to 1991 and then by H&R1871 up through 1999 - When Marlin purchased the H&R 1871 machinery, production of the 999 ceased. The pre-WW2 production Sportsman 999 were the most accurate .22 target DA/SA of their time. The Model 199 SINGLE ACTION only SPORTSMAN was also made and the lock work was taken directly from the Model 195 USRA (both pistols were designed by Walter Roper). The 199 won some world records for a target revolver in the early 30's.
Top: Pre 1930 Bottom: post 1932
IMG_1236.jpg
Top: 1952 Bottom: 1953
IMG_1297_2.jpg
Top: 1939 Bottom: 1953
IMG_0210.jpg

Last edited by 32 Magnum; February 5, 2012 at 04:11 PM.
32 Magnum is offline  
Old February 5, 2012, 04:06 PM   #4
32 Magnum
Member In Memoriam
 
Join Date: January 17, 2009
Location: Eastern PA
Posts: 364
A couple early SPORTSMAN examples and a couple later examples:
Top: Late 1932 Bottom: very Early 1933
IMG_0162.jpg
Top: Early 1933 Bottom: mid 1933
IMG_0168.jpg
A "matched pair of examples from (1994)
IMG_0230_2.jpg

Last edited by 32 Magnum; February 5, 2012 at 04:15 PM.
32 Magnum is offline  
Old February 5, 2012, 04:07 PM   #5
jakeLC
Member
 
Join Date: July 26, 2011
Location: Plainfield, IN
Posts: 49
Thanks

Thanks jim that was extremely helpful i think i will be looking for a 999
jakeLC is offline  
Old February 5, 2012, 04:08 PM   #6
Webleymkv
Senior Member
 
Join Date: July 20, 2005
Location: Indiana
Posts: 9,847
The 922 is a "pull pin" revolver meaning that the frame is one solid piece and to load and unload it you have to pull the center pin out, remove the cylinder, and poke the cartridge cases out of each chamber one at a time. Once the chambers are empty, fresh cartridge may be inserted and the cylinder and center pin placed back into their respective position in order to reload the gun. While slow to load and unload, revolvers of this type are comparatively simple and easy to manufacture and, as such, could be sold for very reasonable prices.

The 999, on the other hand is a "top-break" revolver with automatic extraction similar to the S&W Model 3 or British Webley. To load and unload this type, all you have to to is unlatch the barrel catch and the barrel/cylinder assembly will hinge downward. As the barrel hinges down, the extractor star will raise up out of the face of the cylinder and push all of the cartridges/cases out of their chambers to fall free of the gun. When the barrel assembly get near the end of its travel, the extractor will snap back down flush with the face of the cylinder ready for fresh cartridges to be loaded into the chambers. Once you've placed fresh cartridges into the chambers, you simply have to rotate the barrel and cylinder assembly back up until the barrel catch re-engages and locks the action closed. The entire process probably takes longer to explain than to accomplish. While this is probably the fastest type of revolver to load and unload, the hinged frame is one of the weakest types (though it's not really an issue with a .22) and also is the most complex and expensive to manufacture.

Most modern revolvers use neither "pull-pin" nor top-break systems and rather use either a gate-loading or swing-out cylinder system. With a gate-loading revolver, a loading gate immediately behind the cylinder (usually on the right hand side of the gun) is rotated open to expose one chamber. Empty cartridges are pushed out of the chambers one at a time with an extractor rod housed underneath the barrel with the cylinder manually indexed by the shooter to line each chamber up with the gate and rod. To reload, fresh cartridges are inserted into each chamber one at a time and the loading gate rotated to the closed position afterward. Gate-loaders are usually single action revolvers patterned after the Colt Single Action Army.

A swing-out cylinder gun has a crane which allows the cylinder to swing out of the frame to one side (usually the left) for loading and unloading. The shooter actuates a cylinder release (the release works slightly differently depending on the make of gun) and swings the cylinder out. Once the cylinder is swung out, the shooter manually pushes an extractor rod which raises an extractor star to push the cartridges/cases out of their chambers to fall away from the gun. Releasing the extractor rod allows the extractor to return flush with the cylinder face so that fresh cartridges can be inserted into the chambers. Once the cylinder has been reloaded, the shooter simply swings it back into the frame until it locks into place to make the gun ready to fire again. Most modern double action revolver including those made by S&W, Ruger, Colt, Taurus, Charter Arms, and Rossi use a swing-out cylinder.
__________________
Smith, and Wesson, and Me. -H. Callahan
Well waddaya know, one buwwet weft! -E. Fudd
All bad precedents begin as justifiable measures. -J. Caesar

Last edited by Webleymkv; February 5, 2012 at 04:31 PM.
Webleymkv is offline  
Old February 5, 2012, 04:21 PM   #7
32 Magnum
Member In Memoriam
 
Join Date: January 17, 2009
Location: Eastern PA
Posts: 364
Not all 922 were eject one at a time - sometime around 1948-49, H&R came out with the "all-in-one" ejection system. A keyed barrel bushing inside the cylinder could be pushed out using the cylinder pin to eject all spent cartridges at the same time. Check out this example from 1952. This system was dropped before 1973 introduction of the transfer bar ignition system to this model.

IMG_1288_2.jpg

IMG_1288.jpg
32 Magnum is offline  
Old February 5, 2012, 04:24 PM   #8
32 Magnum
Member In Memoriam
 
Join Date: January 17, 2009
Location: Eastern PA
Posts: 364
JakeLC,
Happy to help out - You're welcome and thanks for thanking.
32 Magnum is offline  
Old February 5, 2012, 08:57 PM   #9
roaddog28
Senior Member
 
Join Date: March 15, 2009
Location: Fallbrook, CA
Posts: 859
I had a 922 and a 949 convertable. My 922 was a hexagon barrel made around 1940. It was my first revolver I ever owned. Some years later I bought a unfired 949 convertable with box. It had the transfer bar and a loading gate which a person could rotate the cylinder half cocked for loading and unloading rounds. Very good shooter. I did sell both of them in later years to finance other handguns. But if I could find a 999 sportsman I would buy it in a heart beat. Jim, you know your H&R revolvers.
Regards,
Howard
roaddog28 is offline  
Old February 6, 2012, 12:26 PM   #10
32 Magnum
Member In Memoriam
 
Join Date: January 17, 2009
Location: Eastern PA
Posts: 364
Thanks Howard. It's taken almost two decades of research and BUYING as well as a lot of research by my friend and colleague the late Bill Goforth - to move the H&R firearms into the very edge of the collectible gun spot light. There's new info coming in every couple months and new variations as well as a new model or two are still being "discovered" or, more correctly, uncovered.
32 Magnum is offline  
Old February 6, 2012, 09:15 PM   #11
MOshooter65202
Senior Member
 
Join Date: February 16, 2011
Posts: 470
Lots of good information on the H&R Revolver.
I've had a H&R mod 999 sportsman w/6" barrel since 1976 which was my very first handgun at 11 years old,I have shot a lot of rabbits and squirrels with that revolver.
MOshooter65202 is offline  
Reply

Tags
922 , 999 , h&r

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 04:50 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.08626 seconds with 8 queries