The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old September 19, 2011, 06:35 AM   #1
billtheshrink
Member
 
Join Date: May 9, 2005
Posts: 67
Many questions

I have reloaded some 38 specials. In my S&W Air Weight all is fine. In my friends ,38 Taurus the cartridges dont slip in or out easily. I have NO idea why..... except some of the rounds were 'mistakes' and i used kinetic bullet puller then re made them with NEW projectiles....but did not RE SIZE (because they already had live primers and were resized with optriginal loads).

So the question is : If i remove the depriming pin from the Dillon die, can or SHOULD i run the cartridges throuh the rezizing die? All thoughta and input is appreciated!!!

thanks
Bill
billtheshrink is offline  
Old September 19, 2011, 06:53 AM   #2
Shootest
Senior Member
 
Join Date: February 9, 2011
Location: Just outside Cleveland, Ohio
Posts: 605
Quote:
If i remove the depriming pin from the Dillon die, can or SHOULD i run the cartridges throuh the rezizing die? All thoughta and input is appreciated!!!
Not if a bullet is seated already. Get a LEE factory crimp die if you want to size after seating, it is made to size at maximum and will not (should not) under size the bullet.
__________________
The private ownership of firearms is an American Heritage. Anyone who disputes that is Anti-American and unpatriotic.
NRA Life Member
http://s1096.photobucket.com/albums/g327/Wynn3/
Shootest is offline  
Old September 19, 2011, 07:42 AM   #3
hodaka
Senior Member
 
Join Date: April 23, 2006
Location: South Texas
Posts: 1,819
My guess is that you did not have the sizing die adjusted properly when you first sized them. I have resized brass after priming a few times by removing the decapping pin, but never with bullets seated. I don't think they would fit in the die, plus it is not very safe. Your friend's pistol must have tighter chambers than your S&W. I would simply shoot them in the Smith and make some more checking to see if the sizing die is properly adjusted. 90% of the problems I have ever had reloading have been with the sizing die adjustment. Good luck.

Last edited by hodaka; September 19, 2011 at 04:57 PM.
hodaka is offline  
Old September 19, 2011, 07:56 AM   #4
reloader28
Senior Member
 
Join Date: October 13, 2009
Location: nw wyoming
Posts: 923
You'd be better off just shooting them, then reloading them right.
reloader28 is offline  
Old September 19, 2011, 08:41 AM   #5
wncchester
Senior Member
 
Join Date: December 1, 2002
Posts: 2,832
The cases are probably rubbing the chamber at the mouth, try tightening the crimps just a tad.

It's very unlikely that not resizing and reseating after bullet pulling will cause any problems at all, it sure won't make cases swell any bigger than they were the first time.

You can easily/safely size and save the primers in any cases simply by removing the decap pin.

You can run loaded rounds into a sizer die (with the decapper removed obviously) as safely as you can run loaded rounds into a seater die.
wncchester is offline  
Old September 19, 2011, 03:20 PM   #6
studman5578
Senior Member
 
Join Date: March 4, 2009
Location: Varying between 1 and 3 hours from Chicago
Posts: 152
I would say that you should not and cannot size a round with a seated bullet. I know part of sizing is so that the neck is narrow enough to hold on to a bullet (meaning it is appreciably significantly narrower on the inside of the mouth than the bullet is). Trying to size a loaded round will suage the the bullet (successfully if you're using cast, and most likely unsuccessfully if you're using jacketed) and will make the bullet nolonger fit the gun. You also run the risk of the loaded round getting stuck in the sizing dye when you try to jam it in when resizing.

A round that fits in your gun should fit in your buddies too. I would have him clean out the chamber well. I had issues with a 357 mag that had a dirty cylinder and the rounds wouldn't seat fully, but that was caused by something else.
__________________
Rev 5:13 "To him who sits on the throne and the Lamb be praise honor and glory and power, for ever and ever"
studman5578 is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 03:50 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07834 seconds with 9 queries