The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Smithy

Reply
 
Thread Tools
Old August 19, 2011, 01:27 PM   #1
colostomyclown
Senior Member
 
Join Date: February 22, 2009
Posts: 613
polishing Shotgun barrel bore.

So I followed some given advice, bought some 000 extra fine steel wool and wooden dowels and used them by hand and with a drill to polish some rough shotgun bores I had inherited, cleaning up the chamber and the bore and it looks great.

Am I doing this correctly? I just want to make sure I'm not removing any protective the layer in the bore that will cause it to pit out of control or bulge or anything or threaten headspace. Like I said I'm using 000 extra fine steel wool and some oil like Honing oil or 3-in-1 oil...

also, does a smooth shiny bore help patterning at all? I know a polished chamber will alleviate feed issues, are there other benefits as well?
colostomyclown is offline  
Old August 19, 2011, 02:04 PM   #2
Edward429451
Junior member
 
Join Date: November 12, 2000
Location: Colorado Springs, Colorado
Posts: 9,494
It wont foul as fast as it did before.
Edward429451 is offline  
Old August 19, 2011, 02:16 PM   #3
colostomyclown
Senior Member
 
Join Date: February 22, 2009
Posts: 613
thanks, I did not know that.
colostomyclown is offline  
Old August 19, 2011, 05:49 PM   #4
Slopemeno
Senior Member
 
Join Date: January 19, 2007
Posts: 2,341
I'd be careful to not egg out your bore that way. A brake cylinder hone in a very fine grit is a better call.
Slopemeno is offline  
Old August 19, 2011, 06:12 PM   #5
Dfariswheel
Senior Member
 
Join Date: May 4, 2001
Posts: 6,817
It would take a LOT of steel wool to egg shape or remove significant metal from the bore.
As long as the bore isn't chrome plated you won't harm it.

Strangely, for reasons they didn't quite understand, the American Rifleman Tech Staff once did a test in which the groups tightened when the choke area was roughened up.
Repeat, this was ONE test and ONLY the actual choke area was slightly roughened.
Dfariswheel is offline  
Old August 19, 2011, 08:38 PM   #6
highvel
Senior Member
 
Join Date: January 21, 2010
Location: Powhatan VA
Posts: 633
The theory is a rough finish on the choke will slow the wad and start shot to string, thereby tighter pattern.
__________________
Do not argue with an idiot. He will drag you down to his level and beat you with experience.--Mark Twain

"I have opinions of my own 'strong opinions' but I don't always agree with them."--George Bush
highvel is offline  
Old August 19, 2011, 09:21 PM   #7
James K
Staff
 
Join Date: March 17, 1999
Posts: 19,131
Anyone know when that test was run by the AR staff? It sounds like it might have been before use of plastic wads, when the thick over-powder wad sometimes broke up the pattern as it exited the bore.

Jim
__________________
Jim K
James K is offline  
Old August 19, 2011, 11:22 PM   #8
colostomyclown
Senior Member
 
Join Date: February 22, 2009
Posts: 613
no chokes here, folks. Have now done four shotguns, an 870 tactical, 1981 police wingmaster and two 590a1s. all cyl or imp cyl barrels. All look like a mirror now and I didn't have to wail on the barrels too hard. 6 or 7 vigorous passes in conjunction with some wd-40 or 3-in-1 and now the chambers and bores gleam.

i was having some issues with the 81 wingmaster the other day. had a +2 extension on it and the gun started off fine. after burning through about 50 rounds, it wouldnt like to eject shells properly depending on my pump technique. if i racked slow, like the movies, a deliberate chik-chak, the gun would function fine. however, if i racked how ive been taught and how a prefer, a speedy forceful quick back and forward, shells would hang up and not eject. i was not short stroking. could this have been due to the rough chamber? or was the extension put on incorrectly and the spring hanging up possibly?

Last edited by colostomyclown; August 19, 2011 at 11:27 PM.
colostomyclown is offline  
Old August 20, 2011, 12:07 AM   #9
T. O'Heir
Senior Member
 
Join Date: February 13, 2002
Location: Canada
Posts: 3,135
"...000 extra fine steel wool..." 0000, but we know.
"...any protective layer in the bore..." There isn't one. The bore has nothing whatever to do with head space either. That's entirely a bolt/chamber tolerance.
__________________
Spelling and grammar count!
T. O'Heir is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 02:47 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.08389 seconds with 7 queries