The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old August 16, 2011, 12:41 PM   #1
TX Hunter
Senior Member
 
Join Date: February 11, 2010
Location: East Texas USA
Posts: 1,776
Pressure question ?

I am loading 39 grains of IMR 4895 and firing a 147 grain boat tail full metal jacket bullet for my 1916 Spanish Mauser 7.62 with 20 inch barrel. Im using .308 brass. The recoil is mild and the accuracy is good, but i want to know the pressure of this load as i am trying to be safe with this old rifle.
TX Hunter is offline  
Old August 16, 2011, 12:56 PM   #2
Jim Watson
Senior Member
 
Join Date: October 25, 2001
Location: Alabama
Posts: 10,905
I don't think there is any reasonable way to know the chamber pressure of a load picked out of the air or off the internet, or even out of most manuals.

But to get you in the ballpark, that is a full grain BELOW the Lyman STARTING load for a 150 JSP at 32,000 CUP.

So I am betting you are well below the pressure of the 7mm the gun was originally built for and have a safety margin even with Spanish gunsmithing.
Jim Watson is offline  
Old August 16, 2011, 01:21 PM   #3
TX Hunter
Senior Member
 
Join Date: February 11, 2010
Location: East Texas USA
Posts: 1,776
thanks

Thats what i was trying for, the Cases look great after firing also.
TX Hunter is offline  
Old August 16, 2011, 02:15 PM   #4
Unclenick
Staff
 
Join Date: March 4, 2005
Location: Ohio
Posts: 10,188
I thought the Spanish conversions had 21" barrels, but my memory plays tricks on me now and again.

QuickLOAD thinks you'll have about 31,800 psi with a large case like a Winchester and about 35,700 psi with a tight case like an IMI. This is with mild primers and the bullet seated one caliber into the case neck. With a 20" barrel, it estimates 2325 and 2400 fps for those pressures, respectively. With all the variations in bores and chambers it could be a good bit different. Actual measured velocities would make a better estimate possible.

The same program suggests about 37 grains of IMR 3031 would fill the case just as well or better and would give you maybe just 500 psi more pressures, but, being faster, would burn more cleanly and completely and would get you another 50 fps or so of velocity.
__________________
Gunsite Orange Hat Family Member
CMP Certified GSM Master Instructor
NRA Certified Rifle Instructor
NRA Patron Member

Last edited by Unclenick; August 16, 2011 at 02:54 PM.
Unclenick is offline  
Old August 16, 2011, 03:00 PM   #5
TX Hunter
Senior Member
 
Join Date: February 11, 2010
Location: East Texas USA
Posts: 1,776
i think your right about 21 inch barrel. If this is a Safe load im happy with it. I would like to load a 150 grain soft point in it also for short range hunting as well. Will probably use the same 39 grain powder charge with a 150 grain Round nose. Thanks for the help guys. PS I forgot to mention that i am using CCI standard large rifle primers.
TX Hunter is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 01:38 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07150 seconds with 9 queries