The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting > Bullet Casting

Reply
 
Thread Tools
Old August 10, 2011, 02:44 PM   #1
kealil
Senior Member
 
Join Date: July 27, 2011
Posts: 214
Cast iron pot

Hey all,
Just curious, can a normal cast iron pot be used to melt lead? Had one laying around, thought I'd ask before 10 pounds of molten lead goes flying.

Cheers!
kealil is offline  
Old August 10, 2011, 04:07 PM   #2
hornetguy
Senior Member
 
Join Date: January 14, 2011
Location: on the north side of DFW
Posts: 803
Yes.. cast iron makes a good lead melting pot.

It would be good if it were cleaned of all oil, grease, etc...

I would heat it up to 300 degrees or so for maybe 10 minutes before putting any lead in it, just to make sure any moisture is baked out of it.

If you are going to be pouring from it, make sure you have hand/foot/body protection.. keep in mind that lead is, um... heavy. Don't put more in the pot than you can safely handle.
hornetguy is offline  
Old August 10, 2011, 04:22 PM   #3
kealil
Senior Member
 
Join Date: July 27, 2011
Posts: 214
Ok good to know. I am not pouring from it. I'm ladling into ingot molds. I'm just tired of cleaning my bottom pour pot after every session
kealil is offline  
Old August 10, 2011, 04:56 PM   #4
dahermit
Senior Member
 
Join Date: October 28, 2006
Location: South Central Michigan...near Ohio, Indiana.
Posts: 3,535
Plumber's pots traditionally have been made out of Cast Iron. There are not as common as back in the day when wiped joints on lead drain pipes were the norm.
dahermit is offline  
Old August 10, 2011, 05:01 PM   #5
PawPaw
Senior Member
 
Join Date: December 24, 2010
Location: Central Louisiana
Posts: 3,115
Quote:
I'm just tired of cleaning my bottom pour pot after every session
Why are you doing that? I generally have a casting session that ends when the pot is nearly out of metal. Then I unplug it and let it cool. When it's cool it goes into the box and up on the shelf.
__________________
Dennis Dezendorf

http://pawpawshouse.blogspot.com
PawPaw is offline  
Old August 10, 2011, 06:28 PM   #6
Pahoo
Senior Member
 
Join Date: February 16, 2006
Location: IOWA
Posts: 5,752
Good choice

As others have mentined, cast iron pot is an excellent choice. I use one for the smelting/fluxing process and dedicate my bottom pour for casting. So, in theory, my bottom pour is always fairly clean and only sees clean lead ingots.


Be Safe !!!
__________________
'Fundamental truths' are easy to recognize because they are verified daily through simple observation and thus, require no testing.
Pahoo is offline  
Old August 10, 2011, 06:59 PM   #7
kealil
Senior Member
 
Join Date: July 27, 2011
Posts: 214
Yes that is what I want to do: put clean ingots into the pot for easy maitinence. Besides, I only have a 5lb lee pot so it takes forever to melt the wheelweights into ingots not to mention removing the dries on such a small surface is a PITA.
kealil is offline  
Old August 10, 2011, 11:08 PM   #8
maillemaker
Senior Member
 
Join Date: August 30, 2010
Posts: 1,056
I use an old dutch oven for rendering wheel weights into ingots. Only clean alloy goes into my production pot for casting bullets.

Steve
maillemaker is offline  
Old August 11, 2011, 05:21 AM   #9
GP100man
Senior Member
 
Join Date: August 1, 2007
Location: Tabor City , NC.
Posts: 1,932
Just don`t over load ya heat source with weight & don`t use anything aluminum !!!

Don`t add cold wet (even if it looks dry)scrap or WW to a hot melt let it cool enuff so the added material is`nt submerged .
__________________
GP100man
GP100man is offline  
Old August 11, 2011, 07:42 AM   #10
Doyle
Senior Member
 
Join Date: June 20, 2007
Location: Starkville, MS
Posts: 5,091
Quote:
It would be good if it were cleaned of all oil, grease, etc...
I'm into cast iron cooking and I can share with you a way to clean cast iron of all oil, grease, and cooked-on carbon. Get a container big enough to submerge the entire pot (plastic tote with a lid works great). Put in a pound of lye. Lye used to be commonly available at the grocery store (Red Devil Lye). It's harder to find now. You can find it in the hardware store in the drain cleaner section. My favorite brand is Roebic. Just look for Sodium Hydroxide as the ingredient. Put in 1 lb of lye to about 5 gallons of water. Submerge the pot and let it sit for at least a week. 2 weeks is even better. Take it out (caution, the stuff will eat your skin) and hose it off really well.

If you were going to use it for cooking, you would go to the next step and re-season the pan. For your use though, you just have to get it really dry. Heat it slowly for half an hour or so to make sure all the water has evaporated from the pores before adding lead.
Doyle is offline  
Old August 11, 2011, 07:46 AM   #11
Rifleman1776
Senior Member
 
Join Date: April 25, 2010
Location: Arkansas
Posts: 3,309
I use cast iron for my melting/casting. Some are reclaimed cookers and a couple small ones are made for lead casting, one is an antique.
Rifleman1776 is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 09:29 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.08932 seconds with 7 queries