The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Harley Nolden Memorial Institute for Firearms Research

Reply
 
Thread Tools
Old July 18, 2011, 02:14 PM   #1
ruffie8
Junior Member
 
Join Date: July 7, 2011
Location: NE Indiana
Posts: 4
need help dating and putting a value on this shotgun

I got this H&R shotgun when my dad passed away, all he ever told me was its been in the family since it was new. I was told at one point H&R stoped producing external hammer in the late 1800s. can anyone help get me a closer date and approx value. its had some less than stellar gunsmithing but is still solid,clean shiney bore and fireable.
Attached Images
File Type: jpg h and r 2.jpg (239.4 KB, 79 views)
File Type: jpg h and r.jpg (245.0 KB, 72 views)

Last edited by ruffie8; July 18, 2011 at 02:50 PM.
ruffie8 is offline  
Old July 18, 2011, 07:36 PM   #2
Hawg Haggen
Senior Member
 
Join Date: September 8, 2007
Location: Mississippi
Posts: 11,643
With the homemade stock and hardware store lock bolt 100 bucks tops.
Hawg Haggen is offline  
Old July 18, 2011, 08:16 PM   #3
4V50 Gary
Staff
 
Join Date: November 2, 1998
Location: Colorado
Posts: 16,599
That nut on the lockplate sure gives it a down home horse stable fix-it job look.
__________________
Vigilantibus et non dormientibus jura subveniunt. Molon Labe!
4V50 Gary is online now  
Old July 20, 2011, 01:14 PM   #4
PetahW
Senior Member
 
Join Date: September 19, 2008
Posts: 4,679
It may "still be fireable", but I (for one) wouldn't fire anything off in a gun made with metal that old, unless I had an excellent, fully-paid health coverage; wore armored gloves & facemask - and even then, only with special, low-powered ammo from the likes of PolyWad, RST, etc.

Certainly not with any modern ammo, even "low brass" .

I value my eyes & hands - a LOT !

.
PetahW is offline  
Old July 20, 2011, 02:12 PM   #5
32 Magnum
Member In Memoriam
 
Join Date: January 17, 2009
Location: Eastern PA
Posts: 364
That is a fairly rare "SMALL FRAME/SMALL BORE HAMMER GUN". These were made from 1909 up to around 1921 (last catalogue entries.) 1st issue was in .44 shot shell (.44-40XL shot and Marble .44 Gamegetter with shot capsule) and 28 gauge. Later 20 ga. was added and .410-44 replaced the .44 shot.
The through bolt has been replaced with one that has a square nut on the right side. Originally these were cut to exactly fit from side plate to side plate and thread into the right plate. It is a true sidelock with individual fire control systems contained in each lock. The hammers are driven by coil springs and spring guide, not flat or V springs as is common for that era.
Your pictures are not real clear on my screen - the wear on the furniture is extreme but it 'seems' to be original configuration.
There were only about 5000 pieces made during the production life. Rumor is that this model originated in Belgium and that H&R purchased the design and manufacturing equipment and brought it to the US to set up the line. At the time this model was introduced, H&R was making three single barrel shot guns in two frame sizes (1900 with removable hinge pin and 1908 with snap off forearm - both large frames, 1905 small frame.) Previously, H&R had produced under license, the "ANSON & DEALEY" hammerless gun - from around 1880 to 1884. These were the first hammerless guns made in the US and just about the most expensive shotgun of the period, made in 5 grades. These are now collector items and sell up to $2K+.
The Model 1909 SF/SB hammer guns are highly collectible today, in good to excellent collection they sell at retail for $600 to $1000+, respectively.
In the condition your gun is in, it is still worth a couple hundred bucks mostly as a parts gun.
I purchased a GOOD .44 ss for $800 and a 28 ga in high V.GOOD condition about 8 years ago for $1000. I haven't seen many sold on the major on-line auction sites, since I bought mine - but the last one I did see sell went for about $1200.
h&Radd20.jpg

44XL_remington_box.jpg

IMG_2226.jpg
32 Magnum is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 12:18 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.06370 seconds with 8 queries