The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Harley Nolden Memorial Institute for Firearms Research

Reply
 
Thread Tools
Old February 22, 2000, 10:17 PM   #1
abow905
Junior Member
 
Join Date: February 22, 2000
Posts: 1
Dear Friend:

I own two Browning A5 Shotguns. Thank you for the information available on your Website. However, I was unable to find answers to my primary questions. Hopefully, you can help. First, I would like to obtain manuals for both. Second, determine their age and value.

The older weapon has a serial number of 639C, it is made in Belgium, has proof marks on every part and multiple proof marks on the barrel. The barrel is labeled "Cylinder 12 Special Steel" and has Browning Firearms Ogden Utah stamped in the top. It will chamber a three inch shell, but I am concerned about the intelligence of firing modern loads especially three inch or magnum shells. What is the best load to shoot skeet with this gun?

The newer firearm has a serial number of WT15100499. It has a gold trigger and the seal of the Wild Turkey Federation. It is engraved with the characteristic "Browning" scroll work with a portrait in the middle on the left side. There is a turkey head engraved on the rear of the receiver. Finally, it is numbered 499/500. What is the best load to shoot skeet with this gun?

Thank you in advance for your help with this matter.

Andy
abow905 is offline  
Old February 24, 2000, 05:36 AM   #2
Al Thompson
Staff Alumnus
 
Join Date: May 2, 1999
Location: South Carolina
Posts: 3,605
Hi Andy,

Harley is out of pocket for a bit, but I'm sure he can correct/add to my limited knowledge.

I'm pretty sure you can get Browning to send you a manual for your guns. Won't be the original but should cover the basics.

There is a procedure to adjust the recoil mechanism to handle heavy or light loads. You'll probably need it if your guns choke on skeet loads.

Don't shoot 3 inch loads unless the barrel is specificly marked "2 3/4 and 3 inch". A 3 inch shell will chamber in a barrel that was meant for only 2 3/4, but when the shell is fired, the short chamber raises pressures a great deal!

Most ranges have inexpensive skeet loads available, if not, any # 8 or 7 1/2 load will work fine. Check the local Wal-Mart for the least expensive 2 3/4 loads.

Giz
Al Thompson is offline  
Old February 24, 2000, 06:47 AM   #3
Bulldog
Senior Member
 
Join Date: February 22, 1999
Location: Texas
Posts: 564
That second one there sounds like a Wild Turkey Federation commemorative, or something of the like. It also appears that you have #499 out of 500 that were made, so I'd think twice about shooting it.

Old Auto-5s are increasing in value, as they have been discontinued. A commemorative example would probably be even more valuable. Just for reference, I saw an old beat-up Sweet-Sixteen selling for about $750 at a gun shop.

For what it's worth, my dad has a pair of old Belgian Auto-5s, one from around 1950 (Sweet-Sixteen, I believe), and the other from the early '60s (12ga). He has shot modern 2 3/4 shells out of the 12ga with no problems whatsoever.

------------------
Bulldawg: NRA, GOA, TSRA, Shiner Bock Connoisseur.
Bulldawg's Firearms Page
Bulldog is offline  
Old February 24, 2000, 09:12 AM   #4
Harley Nolden
Staff In Memoriam
 
Join Date: January 8, 1999
Location: Brunswick,GA USA
Posts: 1,884
TO ALL:
No need for me to add to what has been presented. I will send assem/disassem insturctions, w/photos, by separate email to ABOW

hjn
Harley Nolden is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 02:56 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.06446 seconds with 7 queries